 | | 
01-28-09, 08:47 AM
|  | Old guys rule!!! | | Join Date: March 2003 Location: Sea of Tranquility
Posts: 4,521
| | | The 4.6 Track Times Thread
I'm putting together this thread to list your best times and to have a referance for members to access them all in one place. In this thread you should post a brief mod list ie gears/exhaust/cams/headswapped etc and your times including 60 ft, 1/8 ET and MPH and 1/4 ET and MPH. I will also separate the list between normally aspirated (NA) and forced induction (FI). Also include if you were nitrous enhanced (NO2) and the shot used. Include the year and model since there may be other mod motored vehicles included. Times will be listed from best 1/4 ET down (1/8 times will be slotted in the appropriate positions also but list 1/4 as a rule if you have them). You may list more than once if you have times before and after FI.
Rules:
Must be your car or one you have owned.
You must have at least 50 posts or one year membership to be listed. This is to prevent hit and run listings.
Limited to 4.6 engined vehicles ONLY
Time slips are not required but you can include them if you want. BE HONEST. No guessing or artificial timers.
Copy/paste below
Year/Model:
Mods:
FI, NO2 or NA:
60 foot:
1/8 ET and MPH:
1/4 ET and MPH:
I reserve the right to adjust this listing as I see fit. If you have issues or questions please don't hesitate to PM me.
Rick Driver/Ride........................................Sixty. ............1/8 Mile.......................1/4 Mile Induction/Mods 1)04GTMustang/04GT........................1.65.............7.49@ 95.67
2.1KB,3.73's 2)Tim2002GT/02GT..........................1.726............7.6 12@90.92...................11.902@114.16
N2O125,4.10's,X,TB/plenum,CAI,stickies 3)JBVobra/04Cobra...........................1.947........... .7.781@94.32..................11.946@118.61
Eaton,pully,exhaust,tune 4)Flghtmstr1/01GT.........................2.885.............7.9 49@89.85.......................12.267@112.86
Tork Tech IC kit,exhaust,pullies,LCA's,3.73's 5)stangman98/98GT.........................1.60................. .................................12.78@105.45
N/A,P&P PI Swap,Exhaust,4.10's 6)Showtime/99GT.............................1.89............. .8.55@83
N/A,full exhaust,75mmTB/plenum 7)myponyrocks/03GT.......................2.068............8.573@ 87.3..................13.148@108.65
Novi1200,3.73's,TB,full exhaust 8)98COBRA281/98GT.......................2.173.............8.721 @84.35................13.31@108.00
N/A,Stage2 cams,PI Intake,P&P NPI Heads,UDP's,Internals,LT's,3.73's,TB/Plenum 9)laserstang21/00GT......................1.889.............8.61@7 8.22..................13.418@101.53
N/A,plenum,TB 10)bboylobo/01GT.............................1.941............ 8.818@80.01................13.633@102.99
N/A,3.73's,shorties,Xpipe 11)crzyhrse99/99GT.........................1.90..............8.7 8@81.5
N/A,3.73's,exhaust,UDP's,tune 12)squeak93/04GT..........................1.95................ .......................................13.70@100.9
N/A,4.30's,exhaust 13)COramprat/96GT........................1.935.........8.88@78. 56.........................13.827@103.02
N/A,cams,4.10's,intake,exhaust,tune 14)Burning Rubber/00GT...............1.99.............8.98@78.7..... ....................13.92@100.17
N/A,TB,exhaust,4.10's 15)CobraRed96 GT/96GT...............2.05........................... ............................13.97@100.5
N/A,exhaust,UDP's,intake,3.73's 16)mustangman9812/98GT............2.1............................... .........................14.037@98.94
N2O100,410's,exhaust 17)Stan Weiss/00GT.......................2.115...........9.086@7 7.50....................14.097@97.71
N/A,stock 18)98Cobra281/98GT.....................2.06.............9.1@76.9 8.........................14.16@95.94
N/A,PIcams,intake,3.73's
Last edited by COramprat; 05-24-09 at 06:31 PM.
| 
01-28-09, 08:49 AM
|  | Old guys rule!!! | | Join Date: March 2003 Location: Sea of Tranquility
Posts: 4,521
| |
Year/Model: 96 GT
Mods: Cammed, gears, PI intake swap
FI, NO2 or NA: N/A
60 foot: 1.935
1/8 ET and MPH:
1/4 ET and MPH: 13.827 @ 103.02
Last edited by COramprat; 01-29-09 at 09:48 AM.
| 
01-28-09, 09:06 AM
|  | I have more billet on the Stang than most women have shades of finger nail polish... | | Join Date: April 2004 Location: RAF Alconbury, United Kingdom
Posts: 1,205
| |
FYI I think you should add sea level of the track to the list. Will make it easier to compare
Year/Model:2003 GT Coupe
Mods: BBK 78mm Throttle Intake, BBK TL Shorties, SLP Catted X and SLP LM1 Catback, Street tires (17x10.5 Nitto 555 Non-DR), UPR Tubular front end and Coil Overs, MGW Orange handle, FRPP Drive Shaft, Spec Stage 2 w/ Stock fly, 3.73's, RSD
FI, NO2 or NA: Novi 1200 SL (Mongoose kit from MPH) made 360/360 of 5-6#s, Haven't dyno'd yet making 8-9#s, Stock internals
60 foot: 2.0681
1/8 ET and MPH: 8.5725 @ 87.30
1/4 ET and MPH: 13.1483 @ 108.65
Track Recorded at: Santa Pod Raceway, Poddington United Kingdom. 315' above Sea Level
Last edited by myponyrocks; 01-28-09 at 09:11 AM.
| 
01-28-09, 09:08 AM
|  | Official Member | | Join Date: January 2004 Location: Mars Hill, NC
Posts: 496
| |
Year/Model: 98 GT
Mods: Stock NPI H/C/I, JLT Cold Air, Zex Wet Nitrous Kit 100hp Shot, O/R X-Pipe, Dynomax Bullet Mufflers, B&M Hammer Shifter, B&M Shift Kit, 4.10's, and Street Tires
FI, N2O, or N/A: N20 (100 shot)
60 foot: 2.1
1/8 ET & MPH:
1/4 ET & MPH: 14.037@98.94mph
Track Recorded at: Bristol Dragway - Bristol, Tennessee
Last edited by mustangman9812; 01-28-09 at 09:13 AM.
| 
01-28-09, 09:34 AM
|  | Official Member | | Join Date: June 2005 Location: Joplin, Missouri
Posts: 1,073
| |
Year/Model: 2004 GT
Mods:4.30 gears, o/r x, weld in amco mufflers, bbk cold air.
FI, NO2 or NA: n/a
60 foot:1.95 On Street tires. Sumitomo Hrtz 1's.
1/8 ET and MPH:? sorry, don't remember.
1/4 ET and MPH: 13.70 @ 100.9
Recorded at: Mo-Kan Dragway. Asbury, Mo. 980 something elevation. In the end of Sept.
I think we should include Street tires, d/r's or slicks as well. That obviously makes a huge difference.
Last edited by squeak93; 01-28-09 at 09:36 AM.
| 
01-28-09, 10:22 AM
|  | Official Member | | Join Date: December 2006 Location: Philadelphia, PA
Posts: 340
| |
2000 GT 5 speed bought used. Stock that I know of except has TOYO 245-45-17's on stock 17" wheels.
ATCO Raceway
60' 2.115
330 5.915
1/8 9.086
MPH 77.50
1000 11.802
1/4 14.097
MPH 97.71
Best 60' 2.056
Best MPH 98.79 | 
01-28-09, 11:16 AM
| | Member | | Join Date: May 2008
Posts: 15
| |
Year/Model:1999 GT
Mods:BBK shorty equal length's, o/r H pipe, magnaflows, 75mm throttle body and plenum, fidanza flywheel, and SCT SF3 tuner
FI, NO2 or NA: NA
60 foot:1.89 on a 245/45/17 street tire with a 400 treadwear and no tire compound
1/8 ET and MPH:8.55 at 83mph
1/4 ET and MPH:N/A, we dont have a 1/4 mile track. My 1000ft was 10.99 at 93mph | 
01-28-09, 11:58 AM
|  | Official Member | | Join Date: February 2006 Location: Stafford
Posts: 227
| |
2004 GT
Mods: 2.1 kb blower 11psi, 3.73 gears and 315 nitto DRs
60' 1.65
1/8th: 7.49
1/8th MPH: 95.67mph
Last edited by 04GTMustang; 01-28-09 at 12:03 PM.
| 
01-28-09, 02:06 PM
|  | Official Member | | Join Date: February 2003 Location: Dundee IL
Posts: 473
| |
am i going to be able to be included? my car had a 4.6, but now its bored and stroked and is now at 5.0. | 
01-28-09, 02:54 PM
|  | Official Member | | Join Date: March 2005 Location: State College, PA
Posts: 260
| |
Year/Model: 2001 Mustang GT Automatic
Mods: Catted X-pipe, blowmasters, removed intake silencer, 93 octane tune, UD pulley
FI, NO2 or NA: Naturally Aspirated
60 foot: 2.070
1/8 ET and MPH: 8.816 @ 81.30 mph
1/4 ET and MPH: 13.616 @ 102.75
Cecil County Dragway | 
01-28-09, 03:18 PM
|  | SuperMod it doe snot | | Join Date: January 1999 Location: the people's republic of massachusetts
Posts: 12,018
| |
coram I like this idea.. I am going to sticky it.. | 
01-28-09, 08:48 PM
|  | Official Member | | Join Date: May 2006 Location: UCSD/La Jolla
Posts: 1,564
| |
Year/Model: 1996 Mustang GT Automatic
Mods: Built auto w/ 3200 stall, Catted X-pipe, PI intake, magnapacks, Steeda U/D, CAI, 75mm TB+Plenum, 3.73's, 18x9's with KDII's at 16psi
FI, NO2 or NA: Naturally Aspirated
60 foot: 2.05
1/4 ET and MPH: 13.97 @ 100.5
Infineon Raceway | 
01-28-09, 09:31 PM
|  | Official Member | | Join Date: December 2004
Posts: 1,594
| |
Year/Model: 2000 Mustang GT 5 speed.
Mods: K&N intake, 75mm throttle body, RPM upper plenum, UPR catless X pipe, Mac catback, 4.10 gears, self-adjusted Diablosport tune. 28" tall drag radials on this run.
FI, NO2 or NA: N/A.
60 foot: 1.99
1/8 ET and MPH: 8.98 @ 78.70mph
1/4 ET and MPH: 13.92 @ 100.17.
Darlington, South Carolina. Temp was upper 80's and humidity through the roof. | 
01-28-09, 10:09 PM
|  | Official Member | | Join Date: November 2007 Location: Port St. Lucie, Florida
Posts: 844
| |
Year/Model: 98 GT, 5 speed
Mods: bolt on npi w/ pi intake & cams, 373's, street tires
FI, NO2 or NA: N/A
60 foot: 2.06
1/8 ET and MPH: 9.1 @ 76.98
1/4 ET and MPH 14.16 @ 95.94 | 
01-29-09, 09:33 AM
|  | Old guys rule!!! | | Join Date: March 2003 Location: Sea of Tranquility
Posts: 4,521
| |
While weather and DA is a factor a simple note may suffice. I know the track I frequent is 12' above sea level I would have an advantage but if you make plans to run in good conditions you can better your times.
For simplicity sake I will note only those that may be detrimental to their times since seperating for individual conditions would make for a muddled list. What I may do is link your name to the post in this thread with any explanations. That way you can click to a name and read any issues.
Please post your best overall runs only. While you may have better 60's in one run and a better MPH in another we want the best 1/4 or 1/8 ET as that will be the determining factor in where you lie on the list. Also if you only have a 1/8 track that is fine but I want 1/4 times if you have them.
While tires are an issue also it is considered a mod. you can post that on your mod list if you prefer. A full mod list is not required...I will be brief on the listing anyway. Again you can include your mods in your post or sig (Limit to "go-fast" mods please) and I will work on linking it with you listing.
I'll also begin the listing soon...once I get them noted on my home computer and figure out a nice, clean way to post them. Working on that now.
Last edited by COramprat; 01-29-09 at 09:54 AM.
| 
01-29-09, 09:46 AM
|  | Old guys rule!!! | | Join Date: March 2003 Location: Sea of Tranquility
Posts: 4,521
| | Quote:
Originally Posted by mustang50v8 am i going to be able to be included? my car had a 4.6, but now its bored and stroked and is now at 5.0. | Right now I'm just going to be working with 4.6 but since yours is a unique situation I'll include it with the bore and stroke as a mod. Maybe one of the 5.0 mods can work with a list there. Eventually I'd like a self posting database so taht everyone can get involved and update as needed.
Last edited by COramprat; 01-29-09 at 09:48 AM.
| 
01-29-09, 02:11 PM
|  | I have more billet on the Stang than most women have shades of finger nail polish... | | Join Date: April 2004 Location: RAF Alconbury, United Kingdom
Posts: 1,205
| |
Thanks again for doing this. I understand about the elevation thing and keeping the format simple.
Having moved to fairly low elevation England from superhigh elevation Colorado I know how much it sucks looking at other peoples track times and going "wtf I have more mods and run 1 second slower" etc
I'm not sure where the bad effects really kick in but I think anything above 3000' should be listed?
Your project, your call  | 
01-29-09, 06:03 PM
|  | Founding Member | | Join Date: April 2002 Location: Tulsa, Oklahoma
Posts: 457
| |
Looking to break into the 11's this year with a few more mods.
Year/Model: 2002 GT
Mods: 4.10's, rear lca's, o/r x, JLT RAI, 75mm TB, TF plenum, Nitto dr's
FI, NO2 or NA: 125 shot HarrisSpeedworks wet nozzle kit
60 foot: 1.88
1/8 ET and MPH: 8.075 @ 89.44
1/4 ET and MPH: 12.399 @ 113.62
Edit: Thanks for putting this together COramprat! I am surprised Stangnet hasn't had a true et list in this section by now.
Last edited by Tim2002GT; 01-29-09 at 06:05 PM.
| 
01-30-09, 05:43 AM
|  | Old guys rule!!! | | Join Date: March 2003 Location: Sea of Tranquility
Posts: 4,521
| | Quote:
Originally Posted by myponyrocks Having moved to fairly low elevation England from superhigh elevation Colorado I know how much it sucks looking at other peoples track times and going "wtf I have more mods and run 1 second slower" etc
I'm not sure where the bad effects really kick in but I think anything above 3000' should be listed?
Your project, your call  | I was going to ask what would be a good base to show times affected by elevation. I guess 3000' is a good point. Quote:
Originally Posted by Tim2002GT Edit: Thanks for putting this together COramprat! I am surprised Stangnet hasn't had a true et list in this section by now. | Working on the powers that be to set up a true member input database. We will see how this goes and what happens. | 
01-30-09, 07:59 AM
| | Member | | Join Date: November 2008
Posts: 17
| |
I'm gonna post up my early 1/4 mile best run first then below will be my best fully modded run on n20 in the 1/8th, don't have a 1/4 track here in SC...
Year/Model:2003 GT
Mods: Xcal 1, UPR plenum/70mm tb, flowpath catback
FI, NO2 or NA: NA
60 foot: 2.03
1/8 ET and MPH: 8.81@XX
1/4 ET and MPH:13.60@101.XX
cecil county dragway, 330ft elevation
Year/Model: 2003 GT
Mods: Demolet CAI, UPR plenum/70mmTB, FRPP UDPs, O/R prochamber, flowpath catback, FRPP alum DS, UPR solid upper/lower control arms, 3.73's, xcal 1, MGW shifter, BFG gforce sport 275 width street tires, compucar fogger kit -125shot
FI, NO2 or NA: n20
60 foot: 1.98
1/8 ET and MPH: 7.79@91.xx
1/4 ET and MPH:
dorchester dragway, 89 feet elevation | 
01-30-09, 05:27 PM
|  | Official Member | | Join Date: October 2003 Location: fayetteville, nc
Posts: 1,059
| |
Year/Model: 1997 gt with a 98 gt block
Mods: stroked to 302, pi intake, vt p&p heads, cams, 70mm tb, c&l plenum, forged internals, SCT dyno tune
FI, NO2 or NA: NA
60 foot: 2.02
1/8 ET and MPH: ?
1/4 ET and MPH: 13.56 @ 104
New times with the blower coming soon! | 
01-31-09, 01:32 AM
| | Member | | Join Date: November 2008
Posts: 46
| |
iv never gone to a track but i want to someday, love reading everything on these forums im on everyday. i dont have much to input because im new but i hope one day to get out to the track. Car right now has pulleys, mangapack exhaust, k/n drop in, 275s for tires. Would like to put some gears on but its my dd and im worried about gas mileage, since gas up here in vancouver is way more expensive than everywhere else.Hopefull to get to the track this summer and put a bad time up wish me luck. | 
01-31-09, 01:42 AM
|  | Founding Member | | Join Date: November 2000 Location: H Town
Posts: 2,592
| |
I applaud your efforts, but it has been posted before and the list is ongoing for many years now. Bill Putnam has put it together for us. Best 4.6 ET/MPH's - Corral Forums | 
01-31-09, 02:00 AM
|  | Official Member | | Join Date: January 2004 Location: Mars Hill, NC
Posts: 496
| | Quote:
Originally Posted by Winters98GT I applaud your efforts, but it has been posted before and the list is ongoing for many years now. Bill Putnam has put it together for us. Best 4.6 ET/MPH's - Corral Forums | well about time we had a stangnet one | 
01-31-09, 02:00 AM
| | Member | | Join Date: November 2008
Posts: 46
| | Quote:
Originally Posted by Winters98GT I applaud your efforts, but it has been posted before and the list is ongoing for many years now. Bill Putnam has put it together for us. Best 4.6 ET/MPH's - Corral Forums | i dont see the mods on that forum though which is very helpful to see. | | Thread Tools | | | | Display Modes | Rate This Thread | Linear Mode | |
Posting Rules
| You may not post new threads You may not post replies You may not post attachments You may not edit your posts HTML code is Off | | | | | |