Melbourne area stangs

[baglock1]

Aw, damn you know I was going to respond to this because there is a place I went to, but I dont remember the name and I cant give an EXACT location. But if you happen to be in the area look for them to do tint work, I had them work on my ex's tint and it came out great and the guy was nice. The place im referring to is in the Casselberry area on 17/92. Say you take I-4 from melbourne and you get off 436, take it to 17/92 and make a left. Its a few miles on the right hand side. I know there is a consignment shop there, I went there for my daughter too. Its in a very small strip mall visible from the street. I think if you hit 434 you went too far....

Uh, yeah sorry its a little vague I have a terrible memory.

Thanks Rogun, but as Glenn mentioned I live beach side. What I might save in cost by going to the Orlando Metro area, I'd spend x2 in gas.

Erich, OrLackThereOf (that's too long to type, you're OLTO from now on ) --
I'll give them a call and see what he has to offer. I wasn't wanting anything illegal, just the same shade I have now (which is RIGHT at the limit - 28%).

 

[lxsteed]

baglock, check out the guy across from Harris on Wickham road. I think its "Mr. Tint," or "Dr. Tint" Something like that. He's back behind where Extreme RPM motorsports used to be. He did my g/f's stang and it came out great. He also is a mustang guy. He had a clean 86 5.0 coupe.

 

[Wolfhound]

Just got back this morning. I guess Frankies didn't work out well. Whose going to the car show at the Melbourne Mall?

 

[baglock1]

I had the day off today so I was sure to get up at 6:30 and start cleaning the house as soon as the wife left for work. After that, I mowed and edged the lawn. Then I did the dishes. I'll be cooking dinner tonight as well. Why would I go and do something that is so nice and domestic? Why, to make it less of an argument when I tell her I ordered these today .

Rear coilover kit (with springs):

Lower control arms:

As soon as this stuff comes in and I get the machine work done on the Bilsteins and spindles, I won't have any excuse not to install all this crap that's been accumulating in the garage.

 

[Glenn88lx]

You dawg! Here I thought you were going to say it was her birthday or your anniversary. But still, I like the way you think!!

I just ordered a HD TA, C/C plates, H&R SR springs and Adj. LCA's for the new car. I would have loved to get the setup for the rear end you just ordered but I still have to get me a K-member and A-arms first so the good stuff will just have to be added later.

How soon do you think you will have that bad boy all set up and ready for a test session?

 

[baglock1]

How soon do you think you will have that bad boy all set up and ready for a test session?

IF everything goes to plan, I'm hoping to install it all on the weekend of the 16th. That will include:

Griggs Tubular K-member
Griggs Tubular A-arms w/Delrin Bushings
Griggs Bumpsteer Kit
MM CC Plates
MM Coilovers (Front/Rear)
MM Road Race LCA's
99 Spindles
Polyurethane Engine and Tranny Mounts
Griggs Carbon Fiber Spoiler

 

[dg28182]

Just got back this morning. I guess Frankies didn't work out well. Whose going to the car show at the Melbourne Mall?

Hey hey, Cap'n Sarcasm is back.
Me, Dan and Davie are going for sure.
Couldn't tell you about Frankies', I got there right before everyone left.

 

[Wolfhound]

Well maybe you should get there a little earlier.


Just got my power pipe put and injection kit put it. Next on the list is the cams.

 

[lxsteed]

since I couldn't post this on our forum...

 

[baglock1]

since I couldn't post this on our forum...

I'm not a big fan of Fox coupes (blasphemy, I know) but that looks really nice. Simple, not over stated or tacky... It just looks like a good ol' Mustang!

I assume though that's a glare on the C pillar area and not paint oxidation right?

 

[lxsteed]

Right, it was just the angle that the sun was hitting it. It needs another wax though. The quick one I put on a couple weeks ago is about gone thanks to the FL sun.

 

[eric kebbel]

i will say the guy in vero does very good good work hes made some stuff for both my cars an has does some very nice work on others for a very modest [sp] price has done some stuff on a orange lightning thats unreal

 

[dg28182]

Well maybe you should get there a little earlier.


Just got my power pipe put and injection kit put it. Next on the list is the cams.

Hey Cheif, How goes it? Yea sport, sorry I had to work that night.

 

[Topstang2001]

Well maybe you should get there a little earlier.


Just got my power pipe put and injection kit put it. Next on the list is the cams.

Way ahead of you.
Bout time you go back.

 

[Wolfhound]

Way ahead of you.
Bout time you go back.

When is that beast going to be done?

 

[Topstang2001]

When is that beast going to be done?

Well if people would actually start donating to my Get The Beast Back On the Road charity It wouldnt be much longer.
I dont know really.That stroker motor is 3k alone.But like every one knows my cams and other things are aready at TJ's.Pluse Im also getting those new roller rockers for the 4.6.

 

[Wolfhound]

Well if people would actually start donating to my Get The Beast Back On the Road charity It wouldnt be much longer.
I dont know really.That stroker motor is 3k alone.But like every one knows my cams and other things are aready at TJ's.Pluse Im also getting those new roller rockers for the 4.6.

Start knocking out that overtime.

 

[hxcsxekid]

Or you could just sell your body for money. I've never tried it, but it's worth a shot. You could get a second job for a short time.

 

[Wolfhound]

520 and U.S.1 have been slow lately if your looking for extra money you might to find another spot.

 

[Topstang2001]

To hell with those roller rockers.The damn things are 1,750 bucks!Hell with getting a second job to.I work seven days a week I dont need a second job.