Looking to get blown.

[MY Cobra]

Well i have decided since i am going to keep my car that i will look in to getting a blower. Need some help. Point me in the right direction. Kenne or paxton? i have minor mods and would like to know the price range i am looking at. For a decent blower that will not screw me over ( I drive this car 3 to 4 days a week) Trying to keep it within reason on price. Including install. I dunno if i will need a tune or what. I know everybody and there brother asks this. I am getting some cash for christmas so looking to get a blower.

 

[MY Cobra]

bump

 

[lightblade]

depends on what u want, paxton is probaly my top choice for centrifugal blowers, but im saving for the kenne, check out the sites for both and decide whats best for u, im going witht he the kenne bell 9 psi intercooled kit

 

[Gearbanger 101]

If it's a choice between just those two on a near stock daily driver, I'll take the KB any day.

 

[iceman2740]

I'm saving also. After everything I've researched, I'm going to go with the Kenne Bell but can't decide on the 6 or the 9 psi kit. I'm a little concerned about the 9 psi kit being it will be pushing the limit with stock internals.

 

[streetstang03]

KB

 

[streetstang03]

I'm saving also. After everything I've researched, I'm going to go with the Kenne Bell but can't decide on the 6 or the 9 psi kit. I'm a little concerned about the 9 psi kit being it will be pushing the limit with stock internals.

its all in the tune. Call Tim at Modular Ford Powerhouse and get him to set you up with a safe tune on the 9# kit.

 

[Blue Blurr]

go to vegas.... yes i know i had too


Get a KB mine's getting installed right now so in a couple days ill be blown too!

 

[Gearbanger 101]

I'm saving also. After everything I've researched, I'm going to go with the Kenne Bell but can't decide on the 6 or the 9 psi kit. I'm a little concerned about the 9 psi kit being it will be pushing the limit with stock internals.

Well, the 400hp these motors are pushing is kind of on the fence in regards to the limits of the stock pistons and rods. Some have gotten away with it for several thousand miles, where some have walked home. A good tune is important, but that's only going to save the pistons. The rods are going to feel the strain regardless. Were it me, I'd spend a few bucks upgrading the short block ahead of time. But I like to play things on the safe side where a several thousand dollar investment like that is concerned. I'd save a little more and go with the better rods and pistons and the 6psi KB first, then when more money was available, i'd upgrade to the 9psi kit and drive it with confidence.

 

[el_kid_1]

Just get what you feel is better for your car and you are happy with. But my choice would be a KB again!

 

[Black96Snake]

its all in the tune. Call Tim at Modular Ford Powerhouse and get him to set you up with a safe tune on the 9# kit.

I will second this.

www.modularpowerhouse.com

 

[tomustang]

KB + forged internals

 

[MY Cobra]

thanks a lot. What kinda prices am i looking on an install for a KB? leaning toards the 6psi. Untill i can save up for some forged goodies. i know modularpowerhouse has some kits but where to go to get the kb done?

 

[04DarkShadowGT]

Forged internals and twin turbo kit

 

[Gearbanger 101]

thanks a lot. What kinda prices am i looking on an install for a KB? leaning toards the 6psi. Untill i can save up for some forged goodies. i know modularpowerhouse has some kits but where to go to get the kb done?

Well, keep this in mind. If you go with the 6psi KB on one occasion, then later on down the road decide to upgrade to the 9psi specs and go forged internals, you'll have tear the top end down once from the first install, then tear it off again and completely tear the rest of it down to the the internals. And that aint fun. I'd save up a little now and do the internals along with the 6psi kit. Yes it is a little overkill for now, but it will save you the headache and added cost of having to do it twice later on.

 

[MY Cobra]

yea that is what people are telling me to do. forged internals are pretty dang pricey.

 

[MY Cobra]

seems better if i were to just say to hell with it and go with a 04 cobra.

 

[Gearbanger 101]

yea that is what people are telling me to do. forged internals are pretty dang pricey.

Yeah, they can be. But it's a lot more pricey when you pop the cork at 9psi and ruin your engine completely. I'm coming from a pushrod 5.0L to a mod motor 4.6L and the first think I noticed was that everything was about 3-times the price it was for me to build my 5.0L.

This was the best price thus far I could find on upgraded rods and pistons....
http://www.modularperformance.com/m...e=MP&Product_Code=MP100-2100&Category_Code=EK

 

[HaywoodJablowme]

Well i have decided since i am going to keep my car that i will look in to getting a blower. Need some help. Point me in the right direction. Kenne or paxton? i have minor mods and would like to know the price range i am looking at. For a decent blower that will not screw me over ( I drive this car 3 to 4 days a week) Trying to keep it within reason on price. Including install. I dunno if i will need a tune or what. I know everybody and there brother asks this. I am getting some cash for christmas so looking to get a blower.

I just wanted to say the title of this thread is funny. It reminds me of one time in band camp...

 

[CottonBurnerz]

This thread got my blood boils..... me want soopa chargaa too!

I want to learn a lot more about forge internal and supercharger however. Any links would be great. I can read those when I'm bored or something