My $495.00 IC set up

[jivepepper]

My $465.00 IC set up

I'm using a Fmic with 24x12x3" core over all length is 31"
bar and plate design with 3" inlet and outlet. 3" piping from SC to TB with a greddy type s bov/bypass. I kinda copied the BTI setup. I used 1 2.75 reducer from the SC outlet to the first pipe and 2 hump hoses. I have ordered tbolt clamps for all the connectons I'm a poor novice so don't jump on me to bad for my chop job.

Pipes, couplers, and clamps. 140 shipped
Intercooler..........................150 shipped
Bov pipe with flange..............40 shipped
Bov......................................40 shipped
upgraded Tbolt clamps..........55 shipped
Mics stuff..............................40
_________________________________
............................................465.00

SC reclocked.

 

[exindust]

Sick man... just sick...

 

[san~man]

Looks great, but you severly weakened the front bumper by cutting out that portion. Just hope you don't get into a bad front end collision in the future.

 

[jivepepper]

I know but thats how bti intercoolers installs theirs.

 

[loosescrew79]

Thats just one of the sacrafices you have to make to go fast. Hell yeah. Looks goood

 

[stangGT97]

Sick dude... and who says its a hack, you're doing the work yourself so take pride!

 

[Kilgore Trout]

I like those kewl foglights

 

[DCjuggalo]

looks nice, u get the parts off ebay?

 

[BennyBlown2v]

Ok...now my dreams of an intercooler seem to be in reach... Really good job, hope you turn out some good numbers

 

[DTNODYA]

That's sweet! I don't know what you mean by "chop job" but I think it looks damn good.

Kinda off topic: Where did you get those 45 degree cuplers? I need two of em. Are they silicone or rubber too? Thx

 

[WOT]

Looks cool. I am doing the samething. I have about the same into mine minus the bypass. Here is a pic of mine.

I didn't cut the bumper there is plenty of room so as not to cut it up. Unless you have a 4" core, which I might upgrade to in the future.

 

[jivepepper]

Looks cool. I am doing the samething. I have about the same into mine minus the bypass. Here is a pic of mine.

I didn't cut the bumper there is plenty of room so as not to cut it up. Unless you have a 4" core, which I might upgrade to in the future.

Half the intercooler sees no air? I was going to do it that way.

looks nice, u get the parts off ebay?

Yep sure did.

That's sweet! I don't know what you mean by "chop job" but I think it looks damn good.

Kinda off topic: Where did you get those 45 degree cuplers? I need two of em. Are they silicone or rubber too? Thx

The couplers came with the kit.

www.siliconeintakes.com is a good source for tbolts clamps and couplers

 

[Miles]

I just spooged.. fnsweet

 

[WOT]

Half of it is behind the bumper here too. Where is this getting air from? Besides the Procharger, Paxton, and anyother kit besides the BTI kit doesn't cut the bumper. By cutting the bumper if you get into an accident your insurance company can and probably will cancel your insurance.

Either way thet are both seeing the same air.

 

[04gtdrop]

uhh i dont know about them canceling your insurance. Might be able to say they will not cover some or all of the claim if you were found at fualt. But then again, each insurance company is diff....

anywho, looks cool! i dont even have an s/c yet let alone an IC!

 

[MAXX RS4]

Why cut the bumper to allow air to get to it when the bumper cover blocks the air anyway..?

 

[01Steeda]

Thats sweet man... if you dont mind a newb question, how hard is it to reclock the SC? I may do this to mine while the install is being done. :SNSign:

 

[DisposableHero]

can you post all the places you got all these parts from? I'm really interested in doing the same thign.. thanks

 

[White Stang]

Here is some picks of mine

 

[DisposableHero]

wow White Stang... where did you buy all your stuff?