392/393 Stroker and other Misc Parts

Status
Not open for further replies.
All items are located in the San Francisco Bay Area, CA. I am willing to ship the smaller items at the buyers expense. Shipping the larger items will require the buyer to figure out how to get that done as I do not have experience shipping items this large. If there are questions on any items let me know. If you have a specific photo request let me know and I will post it up here.

Here I have listed the components in this motor. It has about 5k miles on it and was in perfect running order when I removed it from my mustang. I have stored it completely covered and protected. Motor has $8-$10k invested in it but my new project does not allow me to use it. I will entertain reasonable offers. I am not looking to part it out at this time.

393/392 NA Custom Built Motor
[SOLD] Chromrmoly Oil PU
[SOLD] Accufab 75mm Throttle Body
150A Alternator
[SOLD] Push Rods
[SOLD] MSD Distributor
[SOLD] FMS Flywheel 50 oz
[SOLD] ARP Valve cover Studs
[SOLD] 351 Accessory Drive Bracket
[SOLD] TFS 351 EFI Intake
[SOLD] AFR Heads 185 (mild port work)
[SOLD] ARP Head Stud
[SOLD] Crane Hydraulic Roller Lifters
[SOLD] Crane 1.6 Roller Rockers (stud mount)
[SOLD] Meldon High Volume Oil Pump
[SOLD] FPS Balance 393 Stroker Kit
[SOLD] Eagle 4340 H-Beam Rods
[SOLD] Girdle
[SOLD] Probe 4032 Alloy Pistons
[SOLD] Clevite-77 Bearings
[SOLD] 4340 Crankshaft
[SOLD] 351 Block
[SOLD] ARP Oil Pan Bolt Kit
[SOLD] Timing Set 351
[SOLD] Custom Ground Cam (Ed@FTI)
[SOLD] Pro-M 80mm
[SOLD] 42lb Injectors
[SOLD] Moroso Oil Pan

Pictures
More Pictures

I have a Lakewood bellhousing that I used on a 351w block. It is SFI but I believe that rating has expired. I would like to get ~$225 for as they go for over $400 new.
I have the pivot ball, fork arm and throw out bearing as well. As you can see in the picture I have not ground the edges down.


Pictures

[SOLD] I have a ford 9" rear end. This came out of a 1967 mustang. It rotates freely and appears to be in working order. I have not personally run it in a car. Other than needing to be cleaned up it appears to be in good shape. I would like to get $300 for it but I will entertain all reasonable offers.

9" Rear End Pictures

I have a ford 351W block that is bare. I believe that it has been bored over 0.030" on the bores already. I have not run it personally as I already have a 351W based motor and as such I have no need for this additional block. I would like to get $150 for it but I will entertain all reasonable offers.

351 Block Pictures

I have a box of misc stock 1987 mustang GT parts. $25 gets all the parts in the basket.

Pictures

[SOLD] I have a complete set of 8 ford 30lb fuel injectors off of a mustang. These were in complete working order when removed from the car and have been stored inside since that time. I am looking to get $150 for them but reasonable offers will be entertained.

Pictures

I have a PRO-M 75mm Bullet MAF. It is the chrome variant and tuned to 30lb injectors. This came off of my mustang and was in complete working order. I have stored it inside since that time. I am looking for ~$100 for but I will entertain reasonable offers.

Pictures

I have an MSD 6BTM up for sale. I would like to get about $200 for but I will entertain reasonable offers.

Pictures

I have a Ford 302W short block out of a mustang 5.0. It was in perfect running order when I removed it from the car to put a larger motor in. I am looking for about $250 for but I will entertain reasonable offers.

Pictures
 
  • Sponsors (?)


Status
Not open for further replies.