cammed 2v's what do they run?

[Mr. Rustypwnz]

since im a slacker and i havent gotten the cams in my car or headers or hell a TUNE yet, im wondering if i should step up my game with a vic jr intake while im at it, and throw a 100 shot on it.. im just wondering because i got i ran side by side with a cammed/worked on lT1 this weekend, that really got me angry, but i know a good running lt can go 12's with modz..

anyway what are most of you guys putting down with ported heads and cams? or that + 100 shot?

 

[BannonJr]

Exhaust cams CAI tune best I did was 13.3 and about 270RWHP

 

[Winters98GT]

I would focus on trap speed, and less on ET. A 300rwhp mustang can run 11's or 14's.

 

[Deleted member 38176]

I would focus on trap speed, and less on ET. A 300rwhp mustang can run 11's or 14's.

A 300rwhp mustang is good for mid 13's here lol

 

[BannonJr]

Never seen a 300hp mustang run 11's in my day

 

[slayerripkdc]

I seen a stock speed density foxbody run high 12's. Just had suspension and very sticky tires. It is possible.

 

[Mike97gt]

Never seen a 300hp mustang run 11's in my day

Depends how the car is setup and if the guy can drive. I used to see a very lightly modded mach 1 ( power wise) run at NED go into the 11's and he had slightly under 300 to the wheels.

BUT he also knew how to drive, his was on 15 inch wheels with skinny's with 4.30's and his suspension was setup perfectly for weight transfer.

 

[scupking]

Stage II cams and headers should be good for 300rwhp and run upper 12s.

 

[ninjastang125]

I have 277 hp and run low 12s I suppose if I had 300 I could run 11s

 

[1fun281]

98cobra281, 330 rwhp, fastest run was 12.6 at 109,shifting 1000 rpms early on horrible suspension, and no weight reduction... I believe 300 can crack an 11 second pass easily.

 

[Mr. Rustypwnz]

you guys give me hope!! lol

 

[ninjastang125]

I ran a 12.2 full interior and stock suspension....so I don't think you are going need spray unless you are lacking in the driver mod department.

 

[Green&GoldGT]

In my opinion, it really depends on your suspension setup, traction, weight, and driving. I'm sure with drag suspension, a full bolt on 2v with trickflow heads cams and full exhaust could run mid to high 11s. There are full drag setups with stock longblocks and stage 1 cams that have ran 11s.

 

[ErikTheBeast]

I ran a 12.2 full interior and stock suspension....so I don't think you are going need spray unless you are lacking in the driver mod department.

Saw a guy with Hitech stage II's run a 12.1 w/ full bolt-ons stock suspension 4.10's and sticky tires.

 

[ninjastang125]

The only guy that Hitech has know of that ran 12.1 was Evan smith and that was a full suspension car that had major weight reduction. Not doubting you just saying. The reason I went with cms over Hitech was because they said that it was not capable of running 11s without major head porting or nitrous. I think that my stage 1 cms cams can perform with hitech stage 2 cams...

 

[scupking]

Saw a guy with Hitech stage II's run a 12.1 w/ full bolt-ons stock suspension 4.10's and sticky tires.

Hmm now I know what my car can run

 

[ErikTheBeast]

Hmm now I know what my car can run

I know I'm hoping for about the same.

 

[98COBRA281]

with a tune, 4:56's, a set of welds on the front, and a diet, im shooting for 11.80's ALL MOTOR. its gonna be hard, and im gonna have to drive the hell out of it, but i think i can make it happen.

but i do have heads/cams/lt's/ebelbrock ect, and full suspension!

 

[navarro98gt]

12.72 @ 106 w/1.8 60' in my auto. Mods and hp numbers below. This was done on ET streets and H&R SS springs.

 

[Mustang92]

The only guy that Hitech has know of that ran 12.1 was Evan smith and that was a full suspension car that had major weight reduction. Not doubting you just saying. The reason I went with cms over Hitech was because they said that it was not capable of running 11s without major head porting or nitrous. I think that my stage 1 cms cams can perform with hitech stage 2 cams...

11.97 @ 113 in my 2000 GT. 3150lb race weight, VT stage 1 cams, stock heads, Crower valve springs, all the usual bolt-ons, bullitt intake, full suspension, 5 speed, 286RWHP back in April 2004.