Search results

  1. gerzen

    superchip computer chip

    yesterday i bougth a used performance computer chip (superchip brand) at ebay, and i have some question for you guys, first it came out of a 90 mustang it was a manual tranny, i have an a 91 auto convaetible stang, so i ve heard that the 9AL computer is the same in both models (auto or manual)...
  2. gerzen

    24 lbs injectos how can i found it in a yunk yard?

    hi guys i have a question, i would like to change the 19 lbs inyectors of my stang and put some 24 lbs unit, but i dont have a lot of money to do it, so for me is cheapper get the injectors from a yunk yard, in some thread i read that the ford trucks have the 24lbs unit, but what year?, what...
  3. gerzen

    fox springs rated?

    hi, im going to change my rear spring in my convertible 91 gt, and because im in a budget im looking for some thing un expensive springs, some ones stocks that i can use to get better ride and specially a better traction to better launchs, ive notice that so many fellas install an a 4 cil spring...
  4. gerzen

    tank gas leak how can i fixed?

    hi fellas, recently i have a very poor mileage, i make the all tune up you know sparks, filters, clean the maf egr, etc, and still have a very poor mileage, but this morning i notice that i have an a gas leak, i found a leak where the tube dispenser gasoline meet the gas tank, it seems a wet...
  5. gerzen

    starter problem????

    hi fellas, well this morning i try to star my stang for go to the work, but i put the key in the ignition switch the fuel pump hear, the tachometer ligth turns on, all normal, but when i turn on the switch i hear an a click and then zero current, the claxon dont work, the power locks dont have...
  6. gerzen

    valve cover leak GT-91 stang

    hi recently i swap mi heads and intake to my stang, i put an a GT-40P heads and a explorer upper and lower intake, also i use a bran new gaskets for all the swap also i change the valve covers gasketes, but las week i theardown the tranny for make some modifications, and i replace the rear main...
  7. gerzen

    96Code

    hi fellas, i have a problem, i ran my KOEO and KOER a few months a go and i get the 96 code, i reset the ecu and the code don´t appears again then one week later i ran again the test and the 96 code appears again, i clean the codes ran again the test and the 96 dont show up, so i ran again the...
  8. gerzen

    AOD trouble

    hi last weekend i go to the 1/4 mille track and ran my 91 AOD Gt convertible, so i make a lot of pass, and at the end of the day y drove the car to my house and when i was near to my house the tranny comes to have a failiure, when i stop te car and when i try to star moving the tranny comes to...
  9. gerzen

    torque converter which one? how it works?

    hi i have a 91 5.0 AOD stang i have the H/I swap 65 mm TB 70 mm MAF, and a 3.73 gears, so the next step is to install a good torque converter for get a better launch, so here is where i need your help, how the torque converter works? i mean i know is like a have to fan in front each other and if...
  10. gerzen

    can a bad Hego sensor make a lose in performance?

    can a faulty Hego make a lose in performance? im asking because i have a 91 code in my KOEO and KOER and i check both Hego and one have a 4.3 ohms at room temp what it means that the Hego have a failure, im going to replace it any way but i just courius if that Hego is make me losing performance...
  11. gerzen

    KOEO test please i need help¡¡¡¡

    hi fellas, yesterday i run a KOEO test and i have the next codes: 1.- 85 - CANP Circuit Failure (O) , that is because i remove the evaporative solenoid, (its a good idea reinstalled? 2.- 66 - , MAF signal below minimum test voltage of .4vdc (O,M,R), Transmission Fluid Temperature Circuit...
  12. gerzen

    MAF question

    hi fellas, well i have a good question for all you gurus of the mustang world, i have a 91 5.0 stang, recently i make an intake, heads and TB swap, so the best way to go was an adding an MAF swap so i check at ebay and get a 70 mm housing whit a maf sensor and they said that the unit was...
  13. gerzen

    Adjust TPS need help please

    hi, i have a problem, yesterday i try to adjust my TPS, but i can´t, i have an 97 explorer 65 mm TB whit his TPS, i try to adjust at .98 or .99, so i conect my DMM the black wire to a good ground and the red one to the green TPS wire, y try to set at .98 so i need to enlarge the holes of the TPS...
  14. gerzen

    e-cam timming

    hi fellas, im new here, and i have a problem, i have a 1982 302 (non roller) stang, and i put a e-303 cam, i make the swap, installing roller lifters, and all the KIT, the problems is that i take some vacum reads and the neddle give me low reads, below the 8 psi, i dont have a vacum leak, im...
Top Bottom
Back
Forums
Menu