Search results

  1. rrudholm

    Hailine Crack in cylinder ?

    I did do a search without any real clues but would the symtoms be the same as a blown head gasket? I did verify that all cylinders have close to the same compression.
  2. rrudholm

    White smoke equal compression

    \
  3. rrudholm

    Finally tuned 262hp rwhp

    OK I used this PCM that no one has heard of called a bullseye power tuner: http://www.bullseyepower.com/pcu.php Mods include: 310ci Shotblock Eddlebrock 60329 Heads E-303 cam BBK 70mm TB C&L 73mm MAF Trickflow Street Intake Accel 24lb Injectors 155lph Fuel Pump 3:55 gears BBK...
  4. rrudholm

    Bullseye Power Module

    Has anyone had experience with this: http://www.bullseyepower.com/pcu.php
  5. rrudholm

    Bullseye Power

    Any one have opinions on this type of tunning: http://www.bullseyepower.com/pcu.php
  6. rrudholm

    Piston

    Does this look like the 1994 year stock piston?
  7. rrudholm

    Stock Pistons What Heads

    What Heads can be used with stock Pistons with FMS E303 cam? Anybody...........I now know Roush 200's won't.:shrug:
  8. rrudholm

    Should I refurbish or get new

    I have some used Roush 200 heads which has a bent valve and weak or wrong springs which causes alot of valve float at higher RPM's. I have to make a decesion here. Do I spend $400 - $450 to have the old Cast Iron Roushes re-worked or do I spend some coin on aluminum. opinions please?
  9. rrudholm

    Bent Valve was the problem

    I just pulled the Roush 200 heads off to find some of the valves have made contact with pistons and one bent valve. The "A" hole that built my engine sold me these heads refurbished. I have learned one thing, I will never buy refurbished anything agian. I have also learned that I don't want...
  10. rrudholm

    Roller Rocker adjustment

    OK, I adjusted my roller rockers 1/2 turn past zero lash. My car runs like its not on all cylinders. I did the cylinder balance test and the codes told me that 3,4,5,6,7, and 8 are weak. I did a compression test on cylinders and seen around 130 psi on all cylinders. This number is low but I'm...
  11. rrudholm

    Need opinion Rocker adjustment

    OK, so I finished adjusting my Crane Cams Rollers becuase they were clattering bad. I adjusted the rockers 1/2 turn. The noise is gone but here is the problem. When I start the car it sounds perfect for about 30 seconds and then it starts sounding like it is only running on 7 cylinders or...
  12. rrudholm

    Hole in piston?

    What are the symtoms of a hole in a piston. There is no smoke but it kinda sounds like its not runing on all cylinders and there is a lot of valvetrain clicking noise. I adjusted the roller rockers but it still sounds the same.
  13. rrudholm

    Roller Rockers

    OK so I think I may have a problem. I have put about 50 miles on my car now with just having the engine rebiult. I got on it through a couple of gears and then the car started misfiring and ticking. I'm wondering if the rockers need to be adjusted. Is it normal to have to keep adjusting...
  14. rrudholm

    Rear end Gears

    What should I expect to pay for labor? I will be supplying the gears. The shop will be supplying the install kit with bearings and clutch bushings. How many labors hours should this take?
  15. rrudholm

    Which tuner is king

    TwEECer RT or SCT Xcalibrator2? What is the most user freindly and will do the best job? opinions please. I have the following mods: E-303 cam, Roush 200 Heads, Trickflow street intake, BBK 70mm TB, 73mm C&L MAF, #24 injectors, 155lph fuel pump, BBK shorties, Pypes X, and Flowmaster cat...
  16. rrudholm

    Got It Running

    I finaly got my mustang fired up after complete rebuild with many mods. Whie it runs, I had to set the idle up above 1K to make it idle at all. I can tell this thing wants to scoot but I still have the stock computer. I'm thinking I will just got to a tune shop and have a chip made. I know...
  17. rrudholm

    sun visors for 94 GT convertable

    Anyone know where these can be purchased? Mine look like crap and can not find at dealer, internet, junk yards or any where.:shrug:
  18. rrudholm

    Getting ready to fire it up for first time

    Quick question for all you Mustang nuts. I'm finally getting ready start my Mustang for the first time after complete rebuild. My question is, while I know I will need to do something with the computer to make this car run right, will it even start after the following mods with stock computer...
  19. rrudholm

    Fuel Lines

    My fuel lines are no good. Ford does not make these for 94/95 Mustangs. I have fuel line and the connectors that connect to my fuel rail is fine but I can not find these Dorman brand plastic connectors that connect to the steel lines by the fire wall. Help here would be appreciated:bang:
  20. rrudholm

    Oil Pan again

    OK. found out that the oil pan doesn't clear the high flow oil pump. When I tightened the bolts the oil pump pushes through the pan just barely though in one spot. The new pan I ordered is: Summit Double Sump 5.0L Oil Pans Oil Pan, Steel, Natural, 5 qt., Ford/ Mercury 1983-93, 5.0L I...
Top Bottom
Back
Forums
Menu