Search results

  1. lead09

    Puller some codes

    Pulled some codes... I did a koeo test and these are the results. My idle hangs really bad, I did most of the mechanical stuff on the "idle checklist" so I pulled the codes. O Codes: 15 - EEC (PCM) Read Only Memory (ROM) test failed - I found some info. Ground and constant power are good...
  2. lead09

    PS Return Line to Rack Fitting???? HELP!

    My return line fitting that screws into the rack is leaking. Not the rubber hose but the actual fitting. No part store lists it and Ford says they no longer make it. The last list price they had for it was $100CDN. :shock: It's one fitting and maybe 8"of hardline! Can I make something work...
  3. lead09

    Five Lug Conv. - Why can't you ditch the stock PV altogether?

    I know there are adapters and plug kits to gut the stock proportioning valve but why can we just remove it? Could you just run the one line right off the MC and run a T off the MC for the other two lines? Is this impossible for some reason? Why leave the stock PV in place?
  4. lead09

    Damm electrical problem...Help!

    Fuse #8 blew on Friday on my way home from work. I throw another one in and it lasts about a day. Now it pops instantly. My understanding is that it does these items: dome light glove box light power mirrors map light radio This is what I have done: -disconnected the radio...
  5. lead09

    Help Went to the Dyno Today! 307hp and 325tq

    So we spent 3 hours making runs and tested the fuel pump and the maf to see if it was pegged because the tunner could not tune out the lean condition that occured at around 4300-4500rpm. We did not go past 5000rpm cause it was too lean. We did make alot more horsepower compared to the...
  6. lead09

    Is this safe to use on my engine????

    Can I use these as connectors for my bypass and pcv system? They are polypropelyne. The only info I can find says that it is chenical resistant but nothing in specific about oil vapor or temperatures. [/URL][/IMG] [/URL][/IMG] They are ideal. They are barbed. I tried smashing one...
  7. lead09

    Installing MM Subframes

    Haha! Here I go! Got a bunch of stuff to install. I'm gonna start with the subframes. I don't like how close I am to all the fuel lines. I'l moe them as far as I can an wrap them in wet towels. I'll have to pop that plug out as well. Any tips fron any one? I'm gonna be using...
  8. lead09

    TPS Sensor Accuracy???

    How repeatable is the idle setting supposed to be? Key on engine off I set it at 0.990V w/ engine on it was 1.007V. I then re-adjusted w/ engine running to 0.970 to make sure it stays under 1 at idle. You can really hear a difference when adjusting past 1V at idle. Is this ok or it my sensor...
  9. lead09

    Help! I've done the checklist and still having idles issues, s/c, cai and maf...

    I was having lots of idle issues, hunting, bucking when crusing at low speeds, high idle most of the time and a 500rpm surge when shifting at lower rpms. Above 4500 it would'nt surge as far as I could tell. I did all the items on the idle check list twice and I ended up with a steady idle...
  10. lead09

    Help! S/C and bad idle...maf?iac?....

    This is the set-up: Trick Flow Upper and lower intake (street or track?, how do you tell them apart?) 30# injectors 255lph pump 140amp alt. powerpipe w/bypass valve C&L 76mm MAF BBK 70mm throttle body (does that sounds right? too small?) Powerdyne BD11A Supercharger (6psi) Full...
Top Bottom
Back
Forums
Menu