Search results

  1. chucks1967

    Power steering leaks

    Im getting very frustrated with this power steering issue... I have replaced the control valve, got all the hose leaks fixed, but now im leaking out of the stud area. Is there any thing I can tighten that will stop this leak? This is my last leak area! Thanks for the help in advance.
  2. chucks1967

    power steering issue

    I have put power steering back in my mustang, and it works great all except for one thing, when I turn to the right it is a very shallow turn, but when I turn to the left it is a very very sharp turn. So obviously I have not assembled it correctly. but what is the problem? Any Ideas 1967 coupe 289
  3. chucks1967

    watter from exhaust?

    I recently replaced my intake with a performer, and now Im getting moisture out of my exhaust. actually its not a lot, but when i rev the engine and look behind the car, there is a wet splotch under each pipe with black carbon... I was thinking it was anti-freeze, and it was leaking arround the...
  4. chucks1967

    new carb and intake runs like crap need some advice.

    Ok so last night i got my stuff but back together.... new intake (performer),old carb(holley 450 model 4360). it fired right up, but that’s the best part of the story. my friend and I took it for a spin, at first I just wanted to get it up to temp so I was easy into the carb and it ran ok not...
  5. chucks1967

    cam question

    when I bought my 67' the fella' I bought it from said it had a cam..... now natrually it has a cam, but what kind of cam... he didnt know. is there a way to determin the cam specs of an unknown cam?
  6. chucks1967

    3 part engine question

    Ok so I am doing a simple intake swap... and everything is/was ok untill I took off the old intake manifold (2bbl intake with 289 stamp on it). I get it off and in the lifter vally there is a 302 stamp? What? so now im confused. is the block not orrigonal. the stamp on the finder says the engine...
  7. chucks1967

    carb question

    my question is about a holley "economaster" 4360. will it work on a eddlebrock performer and will the throttle linkage mount up or will it have to be modified. The car is a 1967 289 2v. If anyone could be of help it would be very appreciated. if I did not provide enough info please ask me...
  8. chucks1967

    Wheel size and back spaceing

    I have a 1967 coupe with stock rear end and would like to know what the largest wheel is that I can put on the rear and it fit well. If any one can make some suggestions on wheel size, and back spacing as well as tire size I would sure appreciate it.
  9. chucks1967

    need help picking a carb and intake combo

    I have an 67 with a 289 2v all stock except for long tubes, and a mild cam. Dont ask me the grind on the cam, dont know it came with the car when I got the car. Stock intake and stock 2bbl carb. I am looking into getting a 4bbl and a nice intake combo, and well Im not the best at this so I would...
  10. chucks1967

    Wheel Ideas

    I need some help with deciding on a set of wheels. Im on a very limited budget and need some new wheels. I also like diferent looks. I have been looking at the crager smooties, or the us wheel 55 series. Give me some feed back and let me know what you think about the two above mentioned wheels...
  11. chucks1967

    Help with transmission kick down

    Hey guys, I got a problem here. I have a C4 trans, and the kick down linkage on the transmission side will not move. The car runs fine, but I have to down shift now that the linkage is not working. I noticed that there is a small gringing in the gear selector when I put it into 1st gear. The...
  12. chucks1967

    Pics of my new 67 "was it worth 5000"

    Well I got some pics, unfortunatly they are at night, but still look kinda good. Let me know if you think that I got a good deal. As I stated in my previous post, I gave 5000 for it. It only has 57K miles on the car and motor. all # match, and runs strong. Its a C code motor. The interior is...
  13. chucks1967

    Was this a good deal?

    I just got a 67 coupe c code 289 for 5000$ no bondo, all new metal on the body, all new suspension, new floor pans, and most of the interior work done. There are little minor things that I have been working on while waiting for my P/S stuff to come in. The car was driveable when I got it with...
  14. chucks1967

    help with power steering

    I have just rebuilt the power steering controol valve on my 67(when I say rebuilt I mean took apart cleaned up the nuckle and brass sleve and put the system back together.) it was not on the car when I got it, but had been swaped out with a non power steering adapter. Now makes a slight popping...
  15. chucks1967

    I have a clatter noise at idle

    s the subject to this thread states, I have a clatter noise at Idle. I have discovered that it is coming from the fly wheel/torque converter area. I just bought the car and know the transmission has been swapped out, but don’t know with what, or what the torque converter stall is(if that makes...
Top Bottom
Back
Forums
Menu