Search results

  1. B

    engine balance test

    i know the KOEO & KOER test but how can i run engine balance test . what exactly to do to enter this test
  2. B

    no crank after aod to t5 conv

    finish aod -t5 conversion and now my engine not crank ???????? somebody told me its couse from nautral sefty switch.... what to do need to do:shrug:
  3. B

    PINION DEPTH

    Anyone know the standard pinion depth for 8.8 mustang rear end ?
  4. B

    CLUTCH CABLE ADJUST

    how to adjust it with firewall adjuster ?
  5. B

    YOUR HELP ASAP

    I have problem with iol pump drive shaft,,,:mad: the drive shaft is ARP #ARP-154-7904... the problem is when i install it from distributer hole the shaft dont reach the pump so it come to be short,i belive this is how to install it with yellow arrow up and the circle base sitting from...
  6. B

    gt40p spark plug wire

    will 180 degree spark plug wire clear the gt40p ford racing headers
  7. B

    trick flow billet chain

    do I need to use the counter bolt inested the standard thrust bolt
  8. B

    moroso girdle

    did anyone install it in his engine
  9. B

    engine code

    hi guys, i have 1990 mustang gt with ((aod to t5z)) .i have pull in code in KOEO today and i have 67 & 96 and i cant run KOER mode. i belive the 67 code for nutral sefty switch and A/C on,i dont have clutch press switch to start engine i have aod sefty switch how to clear this code for A/C i...
  10. B

    VALVE SEAL HELP

    I HAVE FORD RACING VALVE STEM SEAL THAT COME WITH BLACK AND ORANGE COLOURED SEAL ,WHICH ONE IS FOR INTAKE AND FOR THE EXHOUST
  11. B

    what wires to use

    i dont want to use Braided Ground Straps what wire gauge to use to replace the ground wire in the back of driver cylinder head
  12. B

    gt40p user help please

    i have problem to install crane spring part #44308-1 (conical ) on gt40p head,when install big end spring down the small end is too tigth to insert the reitaner on spring and when install small end down :nono: i think its wrong the small end sit up on valve guide base so do i need to machine...
  13. B

    TIMING ADJUST CONFUSING

    today i deside to adjust my timing but i was confusing how to do iy. what the correct procedure for it. what i did is put harmonic to tdc 0 degrres, then i put white marker in it to 14 ,warm the engine,remove spout,then timing ligth ,at this step i was confuse ,what should i do ,do i need to...
  14. B

    MAP sensor

    hi , i have check my engine vucuum line and i found the MAP vucuum line is missing ,wheres the source must be connected to MAP sensor THANKS
  15. B

    piston/wall clearance

    for engine builder.what piston to cylinder block clearance to run with trw forged piston.opinion please
  16. B

    help,,i m confusing

    i do aod to t5z conversion now i have something strange,why i hear gear Grinding:nonono: only when i put gear in reverse and it hard to put in reverse:nonono: .
  17. B

    gt40p+tfs1+n2o

    any body try this sit up
  18. B

    summit maf

    HI ,any good on summit racing mass air sensor
  19. B

    IROC Z

    what do you yhink about iroc z hood scoop on black ford mustang gt 1991. . opinion please cuz im thinking to do it.
  20. B

    gt40p+tfs1+Edel performer

    im going to do this HCI soon :D , need to see your HCI in your stang with parts for both EFI & carburator
Top Bottom
Back
Forums
Menu