Search results

  1. N

    Full length headers?????

    I was looking in to getting a set along with a new off road h-pipe. Mines kinda rusted. I am guessing these will benifit me in the tourq department, right? Also is there anything wrong with flowtech headers?
  2. N

    Still need some advice on my next mod

    Looking to keep it under 400. What sould I get?
  3. N

    A suspension question

    Will adjustable a-arms allow me to adjust ride height any? Also what ould be the benifit of getting them besied the few pounds they would save? Susp mods are Drag srpings and lakewood 50/50 in the rear and 90/10 up front also have ssm liftbars out back.
  4. N

    Help with codes

    Heres what I got 22 31 51 53 54 96 Maybe thats why my car wont start when its warm and runs rich and is lower than it sould be
  5. N

    A basic free mod check list

    I just wanted to start a thread about the free basic mods that can be done. I'll start with Air silencer removed...........let the list begin.
  6. N

    Need some advice on some issues!!

    I have a birthday comming up and I want to get some typ of mod. I'm looking for somthing that wont take a while to do. I was only thinking the distributer because thats mainly the only stock thing and I am not to sure about it working properly at higher rpms. The motor will some times miss at...
  7. N

    New motor wont start when its warm

    When the motor is cold it starts right away. when its hot it just cranks. I have tried with the throttle in every position. I have about 35lb of fuel pressure. At one point i brought the timing from 15 to about 8 and it stuttered alot and then started but it ran like crap. I moved the timing...
  8. N

    Got my new motor ready to run but

    It wont start. It cranks but wont start. I double checked the distributer and it was put in correctly on the compression stroke. I cranks kinda slow. The belt is kinda tight but nothing rediculas. Just put a brand new battery. I thought that I drained all of the old gas (2 yr) out but apparently...
  9. N

    About to put motor back in my car

    Its been about 2 years and my Morso 7qt oil pan was a little rusty. I sanded down the whole thing inside and out, painted the out side of it but the inside had some surface rust that I sanded most off. I was wondering if is ok to use it stll has a little rust color but its real smooth and if I...
  10. N

    Mark VIII Calipers

    I need to get some better stoping power for when I get my motor back in. I was having trouble stoping at the first exit at the track before I had the nitrous. I was looking in to getting the Mark VIII calipers from a junkyard but I figured newer was better. So any way is this a good upgrade. I...
  11. N

    Trick Flow "Track Heat" intake

    I was wondering if anyone knows what this intake flows in regards to CFM? Just wondering if that information is avalible :shrug:. Thanks
  12. N

    Motor being re-built now, but I need a new cam

    Its in the shop now but I want to toss my E-303 cam for a bigger one. Im getting fly cut forged pistons and H-rods put in the block thats being bord .30. Im also getting studs put in. Anyway I wil be using all of the parts in my sig and I was wondering what cam I should get. Or a custome one, if...
  13. N

    BIG Block : Small block

    What makes a big block a big block. Where is the diffrence between a small block and a big block? Is it the degree of the cylinders?
  14. N

    Its finaly time....almost

    Im finaly getting money together to rebuild my motor. I have 2 short block 1 out of a stock 88 stand and the other out of a 90 lincon town car. Im just going to use one of the blocks and the crank out of my old motor or the 88 not sure which is in better condition. My question is that I need...
  15. N

    I just got a motor.

    I just picked up a 90 5.0 out of a lincioln. It was 50 bucks. My friend at the shop that had the motor said some old guy wanted a new motor because this one burned oil. I think its just a ring. I was wondering if this motor had forged pistons? Im going to have it rebuilt, and I was wondering if...
Top Bottom
Back
Forums
Menu