Search results

  1. 7-UP BILL

    Engine Fan temp sensor location.

    Has anybody used the thermostat housing for your fan temp sensor. I have the DC Controlls controller and the sensor I have is parting ways with me. I was hoping to thread a bung into Tstat housing and go that route. Anybody do this?
  2. 7-UP BILL

    Rear rotor alignment after SN95 swap

    I have Foxbody 5 lug axles in my '90. I did the SN95 swap and the rear rotors need about 1/2" more outboard room for the calipers to mount. Has anyone used a spacer between the rotor and axle flange to bring the rotor out. Probably SN95 axles would have been the way to go, but not at this...
  3. 7-UP BILL

    Drivetrain 8.8 spider gear movement

    I'm in the process of upgrading to SN95 brakes. After removing axles, I attempted to reinstall pin into diff but the spider gears moved so the I couldn't insert the pin. How can I realign the gears to insert pin again? Thanks for your responses.
  4. 7-UP BILL

    For Sale Old Mustang Magazines for sale.

    I have MM&FF from 1991to 2007. Super Ford and Super Ford and 5.0 after they merged. Mustang Monthly in same time frame. I have Jan. 1995 issue Mustang Monthly article on Carroll Shelby signed by him at Atlanta SAAC Convention MINT condition. All other magazines are nearly mint. A few have...
  5. 7-UP BILL

    Expired B-31 Anderson Cam.

    Brand new B-31 cam. Bought and am going in another direction. $275 + shipping. Burlington, NJ.
  6. 7-UP BILL

    Cam Selection

    Had to remove heads because of HG failure, so I'm contemplating a cam change. Has an Iskenderian custom now, but would like something with a little more lope. Stock bottom end, Edelbrock 6025 heads, GT-40 tubular, 42's, S-trim Vortech. Suggestions and experiences will be appreciated. Not...
  7. 7-UP BILL

    What Intake Gaskets Are You Using With Success

    Doing HG's on my Fox and pulled out FP 90361's. They have been in since '94 and upon further research, they seem to be stockers. I have GT-40 intake with Edelbrock aluminums. I saw a Ford Racing set that was pricey, but the ports look huge. M-9439-A50. What gaskets are you using with success...
  8. 7-UP BILL

    The Use Of Fel-pro Loc-wire Gaskets.

    After 23 years of babying and some all out blasts, the head gaskets finally went. 10 lbs of centrifugal boost, Edelbrock aluminum heads and a stock bottom end. When I bought the heads in 93 (Performer 5.0), the newest thing was getting your heads cut for the loc wire gaskets. Not wanting to...
  9. 7-UP BILL

    SOLD "new" Ram 26 Spline 10.5" Clutch

    RAM 26 spline 88794HDT clutch. 10.5 " (86-00) 5.0-4.6. Brand new, never used. Comes with pressure plate, disc, throwout bearing and aligning tool. $175. + ship. In South New Jersey. I have a bellhousing for Tremec/5.0L also. $100.
  10. 7-UP BILL

    Msd Checkout.

    I've had my car since new, and did mods back in the early 90's. Gets about 500 miles a year now. Last two years, I'm getting what I think is some detonation when getting on it. When audible, I lift right away. I'm thinking maybe the MSD could have taken a dump? Is there anyway to diagnose it...
  11. 7-UP BILL

    Spark Plug Selection For Boosted Application

    Don't want to get too wordy, but I have detonation when the pedal is hit hard. Normal driving street and hwy is uneventful. A friend at work told me I should go for a colder plug. I did go one colder when I built motor. GT-40 int. Edelbrock heads, 14mm x 3/4 plugs. 3624's were called...
  12. 7-UP BILL

    Pulling Eec-4 Codes.

    I read the "sticky" on pulling the codes and believe I may have an issue along with others. I have done an AOD to 5-speed swap. Applying clutch pedal, I believe, won't work to access codes. I didn't connect neutral safety switch as I always depress clutch when starting. I can't seem to access...
  13. 7-UP BILL

    Detonation After Injector Upgrade And Tune Up.

    Gentlemen. I have a '90 LX that is somewhat modded. Vortech S-Trim, Edelbrock heads, Gt-40 intake and a fairly tame Isky cam. It was cut on a 114 LC for the SC. It had 30 LB inj and a Pro-M "bullet" MAF. I was able to get 42's and a newer Pro-M for a very decent price this winter. After...
  14. 7-UP BILL

    Remote trunk release

    I'm freshening up my interior and want to paint the console. I'd prefer to remove the release button than tape it up. Any advice. Has a wierd kind of clip on it. Thanks.
  15. 7-UP BILL

    '90 Limited Edition carpet options

    I am going to change my carpet but have only noticed two manufacturers on websites, ACC or LMC. Has anybody used these, and can you give your opinions on fit, ease of installation and quality? I intend on using the mass backed in the factory Titanium Gray. I guess quickness of installation...
  16. 7-UP BILL

    Starting issue-'90 LX

    Last weekend I started car for first time this year and took a 30 mile roundy w/ a 1hr stop halfway. When returning and trying to start, car just cranked (about 15 sec) until I depressed gas pedal. It started, but slowly then ran like usual the way home. I did use 1/2 tank gas for this trip. My...
  17. 7-UP BILL

    Fords @ E-Town (New Date)

    Fords @ E-town has been moved back to the summer from November. (Brrr). It will be Aug 7-8-9, 2009. As soon as I get a flyer, I'll post.
  18. 7-UP BILL

    14th annual North Brunswick Police "Cops & Rodders show

    The North Brunswick,NJ Police are holding their 14th annual car show at DeVry Institute on Route 1 on April 27th 2008. This show has averaged over 500 cars for a number of years. Everything is eligible. For more info e-mail: [email protected]
  19. 7-UP BILL

    CHE adjustable control arms

    Has anybody bought these arms and what was your opinion on quality?
  20. 7-UP BILL

    Bumpsteer kits

    I have it narrowed down to either UPR or Max Motorsports. Who has had experience with either, ie: ease of assembly, quality of instructions, and finally quality of parts. Thanks in advance for your expertise.
Top Bottom
Back
Forums
Menu