Search results

  1. J

    HELP - ODOMETER ALL DASHES - WEIRD BUZZING FROM FUSE PANEL...

    So I swapped in a new 4.6 I had a bullitt motor and it took a crap. So I bought a standard 4.6 Mustang motor and dropped it in... I turn the key to accessory and it reads all dashes for the mileage. There is also a weird, loud, constant buzzing coming from the box located in the front...
  2. J

    Parting Out 2001 Bullitt Motor - 21K Miles

    Parting Out 2001 Bullitt Motor - 21K Miles email me at [email protected] as I hardly check board replies or PMs
  3. J

    FS Bullitt Intake - Everything You Need

    FOR SALE – Bullitt Intake 21K miles Includes everything you need for the swap. $1000 shipped for everything. Please email me if you have questions or if you’re interested… I hardly ever check PM’s or board replies. [email protected] Parts List if you bought it separately...
  4. J

    Possible Rod Bearing... Help

    Watch the videos below for the sound... Scenario - I'm getting a ticking / knocking noise from cylinder 8. I originally lost a lot of power, which I thought was due to the tick. I ran the codes and had a misfire in cylinder 4 and 7. So I replaced all of the plugs and coils. Runs great now...
  5. J

    Help Diagnose Engine Knock...

    I’ve got a nasty tick/knock in the motor. It sounds like a rod bearing. The ECM shows a code that cylinders 4 and 7 are misfiring. The car has little power under acceleration and sputters very badly. Prior to this all going down, no codes were thrown, but the car would sputter and cut out...
  6. J

    help... Huge Loss In Power...

    Car sounds completely different at start up... almost hollow. RPM at idle are 700... Car is not putting out as much exhaust and is much quieter at idle and under load... very weak on acceleration...
  7. J

    My New Wheels... Kind Of...

    Here's what they started out as... that's rust with scratched and peeling chrome. Here's what I wanted to do... Here's what I ended up doing. They are going on my silver vert. I had to strip the chrome, sand, primer, sand, primer, sand, paint 3 coats, sand, paint 2 coats...
  8. J

    HELP... More Connection Questions...

    Please post pics of your car so that I can get a visual... I did a swap and can't figure these final connections out. Picture 1 This is a nipple on the back of the intake. What hose connects here? Also please take a picture of the entire line and where it runs to, I think I may be missing...
  9. J

    HELP Me Recconect These Llines On My Swap… Pics Inside…

    I need help putting these connections back together to finish up my swap… The Yellow pen is used to point to the exact piece I need help with… The first one looks like I must have torn the small hose. Where does it attach? (please photoshop the are where it belongs with a red circle if you...
  10. J

    Rear Caliper HELP...

    I swapped my motor and rear end from a v6 to the Bullitt. I've swapped out the complete rear end, so the mounting brackets, moan braces, and all requires elements are there... My question is, is there a difference between the rear calipers? The pads just will not fit over the rotor and seem...
  11. J

    HELP! Cannot Attach Heater Core Hoses...

    I did an engine swap and am down to the last couple of steps. I cannot get my heater core hoses to attach at the firewall. I tried forcing them on, but they just won't go. What's the deal... I've attached an image below and highlighted the area in red...
  12. J

    Need Motor Pictures Desperately...

    I'm in the middle of my V8 swap and need detailed pictures of the front radiator the left side of the motor and the rear area on the passenger side near the firewall. Obviously the V6 radiator and AC lines are different, but I need some pictures to help out. Any GT motor is fine, I just need...
  13. J

    New Gauge Bezels Installed...

    Took about 25 minutes to install. I think they add a lot to the dash and are a huge improvement over the stock look. We did a group buy on them at $39, so other members may be chiming in. I will be doing one more group buy here before Christmas. If you want in, email me at...
  14. J

    Any Interest In These Gauges...

    Not actual gauges, but I have a buddy who has 10 sets of these left... Does anyone have any interest in buying the rest with me? They pop into your existing bezel. I'm getting a set at $39 They are basically the same as the ones in the Simco gauge cluster that American Muscle sells for $269...
  15. J

    Removing AC lines... Help...

    So I'm in the middle of my 4.6 swap and I can't figure out how to get the AC lines out from the tank that bolts to the firewall.
  16. J

    Cam Install...

    Before you say use the search button, I already did... I need a good write up with pictures on how to install my VT Stage 2 cam and how to degree it. Thanks! Jason
  17. J

    4.30 too much for Nitrous?

    Is 4.30 too steep for nitrous? I ask becasue I am afraid of the fuel puddling without the airflow at a high enough velocity in 1st and 2nd. With the shift from first to second being so quick with the 4.30, I'm afraid the time between shifts will be enough to let the fuel puddle and the slow...
  18. J

    Cam and Nitrous or Supercharger...

    I figure that the Nitrous is going to run me $550 and the Cam another $500. I don't think that I can come close to that on a supercharger setup. Estimated numbers on Cam 30-35hp and a 125 shot puts me around 160-170hp. I'm not sure where the supercharger would put me. What are your...
  19. J

    What's a Whole New Lock Assembly Worth...

    I have an ignition lock cylinder, door locks, and trunk lock with a set of keys. I want to sell them, but not sure what the market rate is. Any ideas on a good price to ask for the whole setup?
  20. J

    Nitrous Help...

    Does anyone know anything about this kit and if it's everything I need? http://cgi.ebay.com/ebaymotors/NITROUS-OXIDE-SNIPER-EFI-WET-KIT-MUSTANG-CAMARO-NOS_W0QQitemZ200226558443QQcmdZViewItem?hash=item200226558443& Or this one...
Top Bottom
Back
Forums
Menu