Search results

  1. Lifted94XLT

    Surging Idle Question

    Vehicle in question is a 92 Coupe w/ 87 5.0 converted to mass air w/ X-cam. The rest of the engine specs are in my sig if any of that matters with this issue. I have gone thru the entire Surging Idle Check List a couple times now and everything it checking out.... I have a new IAC, new TPS...
  2. Lifted94XLT

    Hood Bolts

    I searched and couldn't find any answers, so here it goes:: Would anybody happen to know the "bolt specs" for a Fox Mustang Hood?? Apparently I have lost my factory hood bolts and I have sold the aftermarket hood off my car and feel like an idiot driving it with no hood. Figure it would be...
  3. Lifted94XLT

    Tilt Column Swap; Shaft too Short??

    I just finished up swapping in a late 80's tilt column into my 92 airbag car. Everything went pretty easily except the horn wiring which I haven't got to yet, but the intermediate shaft will not mate up to the steering shaft.... the mounting holes are about 1.5" away from each other. I have...
  4. Lifted94XLT

    QuarterHorse vs. AMS PMS

    Hey Guys. I have a 92 Mustang that I just finished up. Engine specs are in my sig. and I'm planning on goin turbo in a year or so, but anyway, I'm trying to decide what tuning software I should go with. there's a HUGE price difference between the two and major features like tuning on the fly...
  5. Lifted94XLT

    Magical Disappearing Brakes - 92 Mustang

    Updated:: Magical Disappearing Brakes - 92 Mustang -- FIXED!!! OK, For all of you that are new to this thread, I am updating this post with a list of everything that has been tried, tested, and done to this vehicle to help fix my problem, and to help catch you up to speed since this post is so...
  6. Lifted94XLT

    Quick Turbo Intercooler ?

    I'm piecing together a DIY turbo kit, and I've come across a guy selling a brand new XS-Power (ebay brand) for $50.... its 160 x 460 x 90 (6.3"x18.11"x3.5") with 2.5" inlet/outlet size.... he's checkin for me if that overall deminsions or just the core size. Anyway, my questions is, will this be...
  7. Lifted94XLT

    Horn Wiring Harness

    What harness does the horn wiring run through? the wire is missing in my car and I wanna run a new one, but want it to be in the right harness. Any help would be appreciated. Thanks --Ryan
  8. Lifted94XLT

    Quick/Stupid MAF ?

    I have a quick, dumb question regarding aftermarket MAF units and their match injectors..... I bought a 76mm C&L MAF calibrated for 24lb. injectors and a factory Mass Air Sensor. Obviously, I have 24lb injectors in the car..... question time..... Does the actual Mass Air Sensor need to be for...
  9. Lifted94XLT

    What Caster Plates are these?

    i bought these tonight used from a guy and I'm not sure what brand they are. Can anyone identify them for me. I needa find the installation instructions. Any help would be welcome. Thanks! --Ryan
  10. Lifted94XLT

    Bad Miss Issue

    Alright guys, I'm stumped and frustrated.... a coupla weeks ago,I got my car started for the first time and it sounded GREAT!! Then, about four days later, it developed a bad miss, so I checked spark and all was good, then I checked compression and found that I lost compression on #7 cylinder...
  11. Lifted94XLT

    Pushrod Adjustment Question

    When the valves are adjusted properly, and after they've been locked down, should be PR still be able to be spun with your fingers? I'm adjusting them to Zero Lash and then goin a 1/4 turn past and lockin them down there (1/4 turn for Race Application according to procedure I'm following). After...
  12. Lifted94XLT

    No Spark when cranking

    Alright guys, I finally got my motor all wired up and ready to start for the first time. I cycled the ignition and it didn't start, so first, I checked fuel pressure, and it was present, so then went to check spark at the coil.... nothing, did a resistance test and it tested fine, but replaced...
  13. Lifted94XLT

    Need a Rear Brake Line Pic Please!!

    I have replaced all my hardlines with aftermarket pre-bent ones form Classic Tube Industries and I went today and bought the center rubber brake line for the axle. As this was a 4cyl car to begin with, I never got to see how the hard line was mated to the "Banjo fitting Block" on the soft line...
  14. Lifted94XLT

    4cyl Spring Length

    I'm puttin in the 4cyl springs into my front control arms, and they seam WAY long! I'm wonderin if in the mix n match of this car to my v8 donor car the springs got mixed up or something. does anyone have the length of the 4cyl springs?? mine measure out to be just about 14"..... any help would...
  15. Lifted94XLT

    2010 Hot Rod Power Tour

    I'm thrashin on my car to get it ready this year. is anybody else planning on goin?
  16. Lifted94XLT

    4cyl to 302 throttle cable

    Is the Throttle cable the same between the 4cyl and the 302?? Also, could somebody do me a HUGE favor and snap a pic of how it is ran behind the motor and hooked to the throttle body? I would greatly appreciate it. IIRC from when I tore the 302 out of the donor, there was a throttle bracket that...
  17. Lifted94XLT

    Crossmember to Trans Mount Bolt Size?

    As the title states, i'm finishin up my 302/T5 swap and put the trans crossmember in today, but I have lost the bolts that attach the trans mount to the crossmember. Does anyone know the specs on these? oh yeah, if it matters, and it probably does, the trans mount is from Prothane. Thanks --Ryan
  18. Lifted94XLT

    Regarding NHRA rules w/ Nitrous

    Kind of a dumb questions as I think I already know the answer, but I wanna make sure. Do I still need to fabricate a firewall in my coupe behind my rear seats (the factory fiberboard one is deteriorated) if I'm gonna have a blow down tube exiting the car? I think I do, but I thought I'd verify...
  19. Lifted94XLT

    Pulley Alignment Issue

    I just got my motor back today and am starting to bolt on the front accessories. I bolted on my underdrive crank pulley to my PP Balancer and my underdrive pulley to my new water pump and this is what I got:: Are there two styles of timing covers or something on these motors? I compared the...
  20. Lifted94XLT

    Just a quick 5.0l conversion question...

    I just went thru the search feature to refresh my memory on some thing as I am about done with my conversion, and while reading thru some threads, I saw something I didn't see when originally researching this swap.... guys were saying that you need the headlight harness too :shrug: I'm swapping...
Top Bottom
Back
Forums
Menu