Search results

  1. Piston

    Vaccum Canisters...

    http://store.summitracing.com/egnsearch.asp?N=700+115+309801&D=309801 So yah i got 9" of vac at 1100RPM's I was thinking of picking this up. Anyone know of another source for vac can that are cheaper/better?
  2. Piston

    Valve Lash?

    Out of Ideas...ready to put a stick of dynamite in the gas tank. I'm just about to give up on my car. I can't seem to figure out why there is smoke coming outta my drivers side tail pipe. Some does come from the passenger but prolly only what it picks up from the H-Pipe. The car runs good...
  3. Piston

    White Smoke out the Tailpipe!!! Frustration Level High!

    Little background... So I just got done fixin smoke out one drivers side tail pipe. Had to retorqe my intake and the problem went away. Per my engine builder I torqued the intake to 14lbs. Now things were fine and smoke was gone. However, I had some vaccum brake assist problems. My gauge...
  4. Piston

    Vacuum in 5.0 at idle?

    What kinda vacuum pressure should I expect at idle? At what point does low vacuum affect the brakes in a neagtive way? At 1200RPM's i was seeing 9lbs. :(
  5. Piston

    Local Shops Near Schaumburg, IL

    I"m looking for a good shop that does suspension work. I got a TQ Arm and Panhard bar I need installed. Can anyone recommend a good shop? Thanks
  6. Piston

    Drag Springs or NOT? With a scare story.

    Well this kinda starts off me making a pass on a two lane road. Making lots of ponies comes with lots of responsiblity that almost bit me in my ass. So I was going 35 in a 55 behind this truck forever and as soon as all the winding curving roads stopped and I was allowed to pass I punched it...
  7. Piston

    CLUTCH & PRESSURE PLATE

    I ordered a new 900 Series RAM clutch (PART # RAM-905) and Pressure plate (PART # RAM-403) to go along with my Fidanza aluminum flywheel. Does anyone see a problem with this combination?
  8. Piston

    331 motor and dip stick acting funny...

    Ok, I'm no genius as to what this could be but I have a 331 stroker and when driving the dip stick comes flying out along with oil. Now mind you it doesn't happen until higher rpm's 5k and higher. What the hell is going on here? I didn't have breather cap at first but I do now and I notice...
  9. Piston

    TRACTION PROBLEMS... Rant

    I'm regretting a lot of past decisions that I made to my car now! :bang: Alright, back when my car was lightly modified I bought some suspension mods. I bought FMC B springs which lowered and stiffened up my ride. I bought Hotchkiss control arms and had the pinion angle done. I bought...
  10. Piston

    Crazy IDLE. NEED HELP!

    Alright so I broke in my new 331 besides the idle surging at times it was mostly relatively calm. I was driving to my hockey game on the highway going 60mph for about 20 mins. Then I got on to a 50mph street and my check engine light came on. I then noticed that my car was idling at 3500 RPMs...
  11. Piston

    Vaccum Problems...

    Does anyone have a vaccum diagram for a 94/95 stanger. Just dropped in a new motor and the project took longer then expected. Now I'm not so sure where everything plugs in. Should have taken some notes... :bang:
  12. Piston

    Need Help w/ Hoods...

    Anyone got a picture of a 94/98 mustang with a 2000 cobra hood? The other hood I'm looking at is the the 95 Cobra R hood. Here are the links to both. 95 Cobra Hood 2000 Cobra Now the techincal question I got I'm running the RPM II intake and wondering if the 2 1/2 inch clearance of...
  13. Piston

    SFI BELLHOUSING & HEADER QUESTION

    Anyone run an lakewood bellhousing with a tremec 3550/tko and long tubes on their 94/95 stang? I'm curious to the brand of Long Tubes you are running. I am looking for 1 3/4 with 3 inch collectors that will fit. I also have an 7qt oilpan that might be in the way. Any help would be...
  14. Piston

    Does anyone have a stroked 4.6?

    I am not sure how reliable a stroked mod motor would be. Coast High Performance offers a 5.1L/310 Cubes stroker kit, has anyone had good experiences with Coast? This would be for a mostly street application, and also see some track time. I though I have heard before that the stroker motors for...
  15. Piston

    Bellhousing...

    Where is the best place to buy new or used (in good shape) lakewood bellhousing for a tremec 3550?
  16. Piston

    Stock Distributor && High Reving Motor.

    Stock Distributor && High Revving Motor. Is the stock Distributor accurate at higher RPM's past 6000? I'm thinking my motor might see something in the upwards of 7200 if it sneaks a little past my 6900 rev limiter (with an aluminum flywheel and balancer)? I don't need that thing misfiring at...
  17. Piston

    1 5/8 or 1 3/4 Full Tube Headers... Help decide...

    Lets see I'm confused as to what to do with my current exhaust system. My new motor is about to be dropped in and I'm wondering if the 1 5/8 Hooker Full Tubes headers are big enough. I'm putting in a 331 stroker with 10.5 compression and a n-91 cam which is something of the like .600 lift (w/...
  18. Piston

    Not your Basic Intake Spacer Question

    Ok. What is the main purpose of these spacers that go between the upper and lower plenum? If I recall some say it will cool the upper better therefore your engine will gain in performance from cooler air. I also know sometimes you may want to run them if your valve covers are to tall. Now the...
  19. Piston

    315's x40R17's

    2003 Cobra Rims-Different Center Caps? I got the 2003 cobra rims with 315's on them on a 10.5inch rim. Does anyone know if they have center caps with the words "GT"? Or even plain black ones? Thanks,
Top Bottom
Back
Forums
Menu