Search results

  1. Miles

    Wire looms / seperators?

    Looking for some nice looking billet / chrome wire looms for my new 9mm FRPP wires. I found some cheap ones on JEGS but they are plastic and are only good up to 8mm wires...
  2. Miles

    Starter Motor?

    Looking for some +1's on my issue and my diagnostics thus far. I think the starter motor is dead on my 97 GT.. Symptoms: - mustang will not start - motor does not attempt to turn over, i only hear 1 click as i turn the key What is working: - all lights, chimes, etc. are working and full...
  3. Miles

    Dyno results - pics + vid

    The guys at Steeda.ca today had some available time to get my car back in and tuned. If you were following the storyline of my car, I went through a lot of hassles last year (not with Steeda) with PI headswap kits, parts, engine teardown in my garage over winter, etc, etc. Now, it's finally...
  4. Miles

    JLT CAI & IAT Sensor - Wire too short?

    As the title says, I purchased a JLT CAI for my 97GT last fall, and was pleased with the installation, instructions, etc. My one question is that the instructions indicated that I had to drill a hole for the IAT sensor, but upon inspection, the pipe already had the IAT hole drilled. So i...
  5. Miles

    Q's for Tuners or Ford Techs

    So my car is at Steeda.ca right now, and has had MMR STII's heads and VT STI's cams installed. They're using an XCal2 to tune the car now and are running into problems with the O2's. Initially, they were not getting any voltage from the front O2's - they replaced them with Ford OEM O2's and...
  6. Miles

    Driver's 02 sensor - 0V ??

    My stang is at Steeda.ca getting tuned after all of their work on it. They had to replace the front O2 sensors as they were giving CEL's with the 'lazy' codes. So with the new O2 sensors on, there is zero volts coming from the drivers side O2 sensor??!? They've swapped with other working...
  7. Miles

    My headswap nightmare: Opinions?

    To make a long story short, I've had a headache for over a month because of my headswap / Parkway / UPS situation; I had received damaged heads thanks to UPS and have been waiting for parkway to receive reimbursement from UPS. To make a long story short, I have 2 options form Parkway: 1.)...
  8. Miles

    Good day for UPS

    Received the following today: - VT Stage 1 NA Cams - BBK Chromed valve covers - MM CC plates Now I just need my MM bumpsteer kit, and my replacement heads from Parkway. Just spoke to Steeda.ca who is doing my install, and they're ready when I am. Just thought I'd share since I'm super...
  9. Miles

    Which cam?

    UPDATE: Ordered VT Stage 1's - being in Canada sold me on'em Long story short: my PI headswap has turned into a circus thanks to UPS damaging my PI headswap kit from Parkway, and troubles dropping the k-member.. so basically Steeda.ca will be doing my headswap for me. In order to ease my pain...
  10. Miles

    Received parkway performance headswap - heads damaged (pics galore)

    ***UPDATE MAY 15th 2006 at 9:32PM*** See my last post on page 2 for the end to this miserable transaction Original post: Well guys, received my headswap kit from parkway performance. To my dissapointment, there is damage, albeit slight (I hope). The heads were shipped in seperate Ford...
  11. Miles

    Power steering pressure hose removal

    Trying to get this little ****** off so i can pull off the front engine cover. I have 3 of the 4 bolts off that are holding the power steering pump to the side of the engine on the drivers side. The 4th bolt is blocked by the power steering pressure hose, which is a 18mm nut. I can only use...
  12. Miles

    Removing heads - any precautions?

    In the middle of doing my headswap: valve covers off, all front accessories are off, engine front cover is about to come off. My question is before I remove the timing chain, do I need to mark any of the links for timing purposes when I come to reinstall it? or is this just done when...
  13. Miles

    Maintenance to do while doing PI headswap

    I'll be getting new spark plugs with the headswap kit, but wondering what else I should while the car is in pieces.. I'm thinking: Clean exterior of fuel injectors Flush radiator coolant reservoir Flush radiator hoses Replace power steering fluid Replace coolant Change oil and filter...
  14. Miles

    Just ordered Parkway Performance headswap kit

    'nuff said :D Yes, P&P heads would be nice along w/ comp cams, but for now this is a good reliable, complete solution for me. Add another headswap groupie...
  15. Miles

    Buying Ford Service manual vs. CD?

    I'm prepping to do the headswap (finally), and I definitely need some better documentation and pics above and beyond my Haynes manual. Does anyone have any experience with the Ford Service Manual (3,000+ pages, reddish/maroon cover) vs. the CD's sold on the ebay that are suppose to have the...
  16. Miles

    Awesom! My lower intake is cracked! Yay

    Well.. I knew at some point this would happen, just didn't think it would happen today. I was installing a sender unti for my Water Temp gauge from Autometer, and was installing in the stock location next to the alternator. I had put it on, but was getting some leaking, so I tighten it up a...
  17. Miles

    Just installed Accufab plennum..

    .. and wanted to just thank all those that contribute to stangnet. My dad is always impressed at how much work I do on the car, and I owe a lot of it to the great info on this site. As for performance, it's pretty damn nice. It would not be the 1st mod to do (I think gears, exhaust, shifter...
Top Bottom
Back
Forums
Menu