Search results

  1. stang9gt

    Much dif between comp 252H and 260H?

    I am putting cam and exhaust on the 86 mustang motor I have in my bronco. It has 35 in tires and I want to make some better torque. I was looking at the comp 260H cam but I can get a good deal on the 252H with lifters. Would there be a noticable difference between the 260H and 252H in...
  2. stang9gt

    86 302 + E7's?

    I have an 86 302 mustang motor in my bronco and someone said I can put E7 mustang heads on and get some power.. This true?
  3. stang9gt

    needed to put came from 351W into 86 roller 5.0?

    I have an 86 mustang motor in my 84 bronco. I want to get the comp cam 260H 4x4 torque cam but it is for a 351W which isn't roller and my 86 5.0 is. Do I just need to get the cam and flat tappet lifters, throw them in and go??
  4. stang9gt

    pics of blue stangs with black bullitt rims with machined lip?

    Anybody have a blue stang with the black bullit wheels that have the machined lip?
  5. stang9gt

    Adding extra clutch/friction to limited slip?

    Anyone add another friction pack/clutch in between the two shims on each side of the limited slip?? Instead of spacer clutch spacer spacer clutch, you would do spacer clutch spacer clutch spacer clutch...It supposed to limit the one wheel spin a little more. Just wondering who has done it and...
  6. stang9gt

    someone photoshop??

    Can someone photo shop the yellow part of this car to sonic blue?? I am thinking of this paint scheme on my blue 96GT minus the ricer ground fx...
  7. stang9gt

    trac lock is shot! how to replace clutches??

    So when I lift my car up I can rotate the tires with the trans in gear without the driveshaft spinning. Trac lock is shot. I can get the rebuild kit for 43$ (new clutch packes, shims, and lock bolt.) How do I decide which shim I need to use when I install the new clutch packs??
  8. stang9gt

    anybody run a spool on their daily driver??

    Just what the q asks....I need to rebuild my rear and was just wondering about these...
  9. stang9gt

    needed to convert to 31 spline???

    What all do I need to convert my 8.8 to 31 spline axles??
  10. stang9gt

    have 3:73's with 290ish rwhp...4:10's??

    I have about 290 to the rear wheels right now...I plan on getting a supercharger sometime over the winter for spring...would it be worth me switching my 3:73's out for 4:10's?? It won't cost me anything but parts!!
  11. stang9gt

    get code without scanner on 99GT?

    Is there a way to retrieve the code on a 99GT without a scanner..Some way to make the dash flash a certain # of times???
  12. stang9gt

    anyone know about 4.6 swap into ranger

    My buddy hydro-locked his 4.0 97' Ranger...I have an extra complete 4.6 laying around and we wanted to know what all would need to be done to possibly put the 4.6 into his truck...Anybody done this???
  13. stang9gt

    gains on my setup with accufab plenum/tb??

    What gains would I expect to see adding the accufab plenum with 70mm tb on my current setup....PI heads, hp blower cams, long tubes, 80mm maf, all other little bolt ons that made 280rwhp...Somewhere around 290 now since I got the cams shimmed and setup correctly....
  14. stang9gt

    remove sway bar on street safe??

    Is it safe to drive around with the front sway bar removed on the street???
  15. stang9gt

    Get 78 302 to 9.5:1????

    I am rebuilding a 78 302 truck motor to put into my bronco...It has been bored 30 over...What cc are the stock heads on these motors??? 56cc??? I am going to get the comp 4x4 cam and I want to get the compression around 9.5:1 or a little better....Also, is it worth switching the motor over to...
  16. stang9gt

    try to install motor today with trans/long tubes

    I tried to put the motor in with the trans and long tubes attached...Not going to happen for me at least...I took the driver side long tube off (cause that one is easy to install with motor in car) and it went right in....
  17. stang9gt

    shaving heads for higher compression??

    I have an 84 bronco with an 86 302 stock from a mustang...How far do I need to shave/mill the heads to get an 10:1 compression ratio??? I want to do this along with a comp torque cam... I just want a little extra power for the 35's...
  18. stang9gt

    Coil pack mount on 96GT??

    I need ideas of other places I can mount them besides the front of the motor...I though about a little extension on the back of my strut tower brace to mount them back near the firewall...
  19. stang9gt

    Pics of engine before install!!!

    Just some pics I snapped of my motor before I stick it in and get it scratched....
  20. stang9gt

    shims for valve tappets???

    I have had two instances over the past 1.5 yrs where two of my rockers just fell off...So HP was going to send me some shims...Was supposed to take 3-4 days, this was two weeks ago...I have sinced talked to HP and they said they were shipped but they still aren't here...My q is, what can I use...
Top Bottom
Back
Forums
Menu