Search results

  1. B

    Will 26X10 ET DRAG be to small??

    I currently have 26X10.50 ET STREETS and I am spinning badly. Heres my suspension set up. tubular k-member,Tubular A-arms,130# coil overs,Strange adj struts,No sway bar,subframes,Megabyte Jr upper and lower's,50/50's,stock spring's. My car has the power to pull high 1.4's to low 1.5's so...
  2. B

    N/A 331 stroker Track Results inside...

    This is the first time out with the new combo. And also my 26X10.50 Et streets are being spun all of 1st gear and a little in 2nd. 1st pass (6000 rpm shifts 60ft=1.68 1/[email protected] 2nd pass(6200 shifts first 2 runs is 32 degrees timing 60ft=1.69 1/[email protected] 3rd pass...
  3. B

    12.00 to high 10's..Whats the difference in SOTP?

    I just put in my new AFR/FTI 331 stroker thats built to run high 10's. Anyways I dont even have 10 miles on this motor yet but I have taken up; to 4000RPM and yeah it does feel considerably stronger than my old motor. But when I do nail it for the first time how much of a difference should...
  4. B

    new track times

    hello, saturday was race day for me and i beat my old et of [email protected]. here's my times: 1st pass--- [email protected] [email protected] [email protected] 60fts were between 1.630-1.645 here's my present combo: gt-40 stock shortblock bassani 1 5/8 stepped headers with x pipe y...
  5. B

    Picked up a Mexican Block today!!!

    Yeah Its a 1971. Any way's out of curiousity How much can you bore them over? Right now its a standard bore. I am Building a 331 using this block but if for some reason something happen's would .060 over be to much?
  6. B

    Went to the Dyno today!!!

    Well the stang put out 310RWHP and 311 foot pounds of torque. I'm gonna try to attach the image but I dont know how. I have the dyno graph in my e-mail but tryin to get it on here is beyond me.. Well never mind I dont know how to attach an image. But yeah the A/F ratio was at 13.8
  7. B

    Is my Fuel sysyem up to Par?

    Alright I'm in the process of building a 331 with AFR 185's, Vic Jr intake, Custom FTI Solid cam, 750 Demon carb etc.. And I'm shooting for very high ten's or low 11's on a bad day. But my fuel sys. consists of a 190l.p.h. EFI pump along with the stock lines and an Two Fuel regulators, The first...
  8. B

    Harland Sharp or Comp Cams Pro-Magnum?

    Which Roller Rocker is better? Planning on Buying AFR 185's soon and they will be 7/16 stud mount. The Harland Sharps are designed for the AFR's where as the Pro-Magnum's are just designed for Ford's
  9. B

    How much of a weight loss? What will I gain?

    Alright 2 week's ago I went a 12.12 with a 1.60 60FT. So I pulled off the front nose and removed the crash guard, Put in a Flaming River Manual Rack Since the power steering was leaking bad any way, and also put on some tubular A-arm's. I already have a Tubular K-member. So what kinda...
  10. B

    Got My Custom Cam! Cam Experts step inside.

    Alright This is A solid Flat Tappet cam. Valve lash is .16 and .18 Intake. exhaust. Gross valve lift, .5280" .5440" Duration@ .020, 264*...
  11. B

    New track times!!!!

    Well the track finally opened up and I ran a total of 7 times.. So any-way's I had a 700 DP and switched to a 750 Speed Demon. Old best was a 12.22 with a 1.61 60ft. Here was today's best. 60ft.. 1.60 330ft..4.96...
  12. B

    timing questions

    hi, i have a 91 mustang gt with the following: stock shortblock e-303 cam, y303 ported heads edelbrock rpm air-gap intake/ 750 speed demon carb full msd ignition system bassani 1 5/8 to 1 3/4 stepped headers / x-pipe tremec 5 speed/ 4.10 posi fastest time has been 12.22 @ 113 mph...
  13. B

    Which carb Would be better?

    I currently have a 750 Speed Demon carb. But was thinking of getting my Holley 700DP back And putting a Pro-Form main body on it. BG says that the speed demons are for cams up to [email protected] so what happens if you run a cam that's 247 and [email protected] Combo is 331 with 10.4comp...
  14. B

    Is this a good cam?

    It's a FL series solid flat tappet. From Comp Cams. specs are, adv. 276,280 .050. 247,251 with .584 .596lift on a 108ls Here's the combo. Built 331 with 10.4 comp. AFR 185's,Victor JR intake and 750 Speed Demon. Bassani...
  15. B

    Did I make A good carb swap?

    Alright I had a 700 Holley DP that was box stock and my Buddy traded me his real new 750 Speed Demon that's also box stock. Was this a good choice?
  16. B

    What Main bearings to use?

    Should I use the standard half groove or 3/4 groove or Full groove? I'm using a Scat Series 9000 cast crank.
  17. B

    Oil pump shaft?

    I was talking to my machinist about oil pump shafts and he said to stay away from ARP and Ford Racing hardened shaft's. And to stick with a stocker because the hardened shaft's if they barely twist will snap and a stocker will not. Like as if there to hard? I'm also running a standard volume...
  18. B

    Anyone use the Canton Main Support?

    Building a 331 soon and need a girdle. Its 1/2 inch thick steel And has a matching windage tray to bolt on it. Are they anygood?
  19. B

    Ford Racind SFI 18-1 Damper??

    Who sell's these for the cheapest? It's for my 331 and I'm looking at the 28.2oz one. The pn is M-6316-C351. Which spacer would I need? The motor will be in my 91 GT. Thanx
  20. B

    Lakewood Bellhousing+Bassani Lt's=??

    Can I use my Basani 15/8 to 13/4 lt's with this bell housing? Is there grinding required? thanx I also have a Tremec 3550.
Top Bottom
Back
Forums
Menu