Search results

  1. Mavrick

    Toploader Speedo Issues

    The stock VSS and speedo gear doesn't seem to want to sit into the tranny very nice. Is anyone out there running a toploader in a fox with a working speedo? Let me know what it takes, Thanks.
  2. Mavrick

    No Spark - Ignition Problem

    Car is a 94 GT and i've got a no start problem. Major static on the radio recently, soon after static was noticed ignition module failed. Replaced module and car ran normal for 3 months... reduced static on radio. Have replaced this module twice, and it runs for a while and then randomly...
  3. Mavrick

    Failed E-test

    Motor is a stock rebuild and the heads have like 600km on them since I rebuilt them (valve job etc). The car runs good, other than a surging idle problem. KOEO I get code 11 - Checks OK. Heads have been milled .010" and i'm using flat top pistons instead of the dished ones out of my 88...
  4. Mavrick

    Help With Trouble Codes...

    I just built a motor and I have it running in the car.. I have a surging/missing idle, and the car likes to stall when coming to a stop sign. Here are the KOEO codes.. These three, I am not too worried about. The VSS and Neutral pressure switch are not hooked up, due to me using a...
  5. Mavrick

    Mark VII Rear Disc Hardware

    I need some anti-rattle clips for these calipers.. does anybody have a part number? They are discontinued through Canadian Tire and Ford.. Napa and Carquest tell me they can't get them either. Anybody care to help out? Thanks,
  6. Mavrick

    2.5" Dynomax Tail Pipes

    I want these pipes.. i understand that Dynomax and Walker are essentially the same company, and i have a buddy who is a Walker dealer. Does anyone have a part number for these tail pipes? What finish do they come in? Can they be polished? Thanks,
  7. Mavrick

    How to clean fuel injectors?

    I have the injectors out of the intake right now, and before i start putting things back together i'd like to clean the injectors, as i've heard of this being done before. Should i soke the tips of the injectors in something, or what? Thanks,
  8. Mavrick

    Putting a motor together.. any tips?

    Turns out the valves are fubar in my current heads, and im weary of the lower end with only 18psi of oil pressure at idle.. so i'm going with a new motor. My buddy's dad has a 302 (306) with a cam, professionally built lower end that i am getting at a great price (500miles on it, if that). I...
  9. Mavrick

    Slight miss/stumble! Please help!!

    My car has a slight miss/stumble i think.. When holding my hand on the intake and observing the motor, it stumbles/jerks once every 3-5 seconds or so. I can also feel air popping out/shooting out of the drivers side tail pipe (shooting a blank), so i think it's on the right bank. When feeling...
  10. Mavrick

    MAP/BAP sensor help..

    Whichever it is on a MASS AIR car. Mine has no vac hooked up to it, just atmospheric pressure. I think its the MAP sensor? Either way.. my car has a slight miss. I can feel the motor jerk every 3-5seconds and i can also hear/feel bursts of air or popping out the drivers side tailpipe. A buddy...
  11. Mavrick

    Codes.. emissions equipment

    KOEO I have code 82 – Secondary Air Injection Diverter Solenoid failure AM1 KOER I have codes 44 and 94 Following jrichker's directions, these are the values i got from the solenoid. Red Wire - 14.3v (constant) White/Red Wire - 0.6v (does not change what-so ever, held the meter on it for...
  12. Mavrick

    Help with Codes...?

    Warmed the car up and read the codes.. (got the car up to 160 before i shut it off) and this is what i got.. KOEO 82 2 3L TC - Fan Control wire shorted to ground - A/C and Fan Circuits OR - AIRB solenoid - Solenoids and Air Injection OR - 3 8L SC - Super Charger Bypass Solenoid -...
  13. Mavrick

    Cross Brace Behind Rear Seat...

    What structural purpose does this cross brace serve? I remember hearing it was fairly important, but i also read that it's a flimsy worthless POS. I have removed mine, but if it serves somewhat of a purpose, i'd weld something better in there or maybe make a brace which would bolt to the top...
  14. Mavrick

    Axle Question.. O-ring?

    I just got a 5lug axle from a ranger, and it has a rubber O-ring where the c-clip slides into. My old 4lug axles do not have these O-rings (i have never used this rear end before, i bought it bare and rebuilt it). Should i buy new ones or not use them at all? Thanks.
  15. Mavrick

    Clutch Disc - Chipped, OK?

    There is a chip on the outter edge of a centerforce DF clutch disc.. previous owned dropped it on the bellhousing. It is a small chip. Will this effect anything? Thanks, and
  16. Mavrick

    Bushing trouble.. hardware siezed to sleeve..

    I'll be tackling my front control arm bushings soon, and wanted to see if anyone has any tips as to how i can go about doing this. A 5gallon compressor and air tools couldn't crack the bolts loose. For those of you who don't know, the bolt that holds the control arm to the K-member has siezed to...
  17. Mavrick

    K Member Brace Install

    I've got an authentic DECH g-load brace, and i tried installing it a few weeks ago but the cats interfered with it, BIG time... not even close to enough space. I have heard of people "massagin" the cats to make it fit, but i think that'd be a whole lot of hammering! Can the brace just not...
  18. Mavrick

    PBR Brake Upgrade

    I'm looking to upgrade to the 99+ PBR brake setup.. As far as i know, i need the calipers, brackets, banjo bolts and lines (or SS lines) to go with my 5lug conversion (as well as grinding the spindles). What should i pay for calipers/brackets/banjo bolts/lines, used? Do they come on ebay...
  19. Mavrick

    New Brake Upgrade!!

    Finally splurged for the SN95 front end upgrade. Got the spindle assembly complete with spindles/hubs/rotors/calipers/pads/flex lines.. for $300 from a local wrecking yard. NOT BAD! Can't wait to put em on.. and if anyone knows of some inexpensive GT wheels i'd most likely be interested in...
  20. Mavrick

    SN95 Front Brake Setup.. is this a good price?

    From a scrap yard, complete front brake setup from a 94-95 mustang.. $300. Including rotors/calipers/pads/spindles/hubs/banjo bolts/flex lines if salvagable. Is this a fair price? Deal? Could i find cheaper? $$ is Canadian mind you.. Thanks.
Top Bottom
Back
Forums
Menu