Search results

  1. M

    Expired 1987 Mustang Notchback Roller Cage Drag Lites Fuel System

    1987 Mustang Notchback: blue exterior and blue interior, 8 point welded in cage, racing harnesses, full length subframe connectors, Steeda Upper/Lower control arms, driveshaft safety loop, lakewood 90/10s, Weld Draglites (bigs/littles), Steeda Caster/Camber plates, full autometer gauges, 3.73...
  2. M

    Need help wiring a relay and temp controller with Electric fan

    hello all...i've done a search for the past week through out this site and no luck with any answers... I'm installing an Taurus Electric fan (3 wires- high, low, ground) on my 1987 notchback. Already upgraded the Alternator. My adjustable controller my relay can't seem to...
  3. M

    Which Headers with Scattershield and....

    i have an 87 coupe...302 with tremec 3550..which long tube headers will fit with windsor sr. heads and my lakewood scattershield? so far, i know mac doesn't fit...looking for 1 5/8 with 2 1/2 collector...tthanks
  4. M

    To do or not to do 5 lug Disc LSC set up on my notch

    picked up a 90 4 banger notch about a month ago and have been collecting parts for it.. My friend is parting out a 91 LSC with 5 lug 4 wheel disc and offered me all the parts i need for the swap for $100. Now is it worth going from stock 5.0 mustang brakes to 5 lug 4 wheel disc from an LSC...
  5. M

    Converting a 1990 4 banger...quick question

    converting a 1990 4 cylinder notch....is the mass air harness for that year specific or the same as other years? i know one of the years the harness had 2 plugs to the dash harness and the other years had 1 plug to the dash harness...thanks in advance
  6. M

    Stupid brake question

    i still have a soft pedal...recently bought a new master cylinder ...i bench bled it, got new front calipers. I switched to a turbo coupe disc rear...the only thing i can think of is either soft rear brake lines going to the rear calipers??? would that cause a soft pedal, i've bled the system...
  7. M

    Not getting power to my harness???

    i have an 88 notch with a mass air harness...i'm pretty much redoing the entire car. The problem i'm having is the solonoid is hott all the time with the battery hooked up. What did i put on the power side of the solonoid that should be a ground??? on the positive side is a brown wire from...
  8. M

    would i benefit switchingto an edelbrock rpm 1 EFI intake?

    my current combo is ported Twisted Wedge heads, 1.6 roller rockers, gt40 intake, 24#inj and maf, 65 mm TB, 10:1 cp, and basic bolt ons. I have an opportunity to get a ported edelbrock rpm intake that is port matched for my heads. Any ideas or input?? thanks
  9. M

    Comp cams Anodized red roller rockers

    i am currently redoing my motor for my notch, but i do not know the torque specs on these rockers...would someone be able to help me out??? thanks in advance http://www.compcams.com/information/Products/RockerArms/AluminumRoller.asp?printer=1&
  10. M

    Rear end swap

    putting a new rear into my 88 notch...just wondering what type of fluid i should use?? and when i put the cover on, should i use silicone or liquid gasket or something to keep the rear from leaking fluid??? thanks in advance
  11. M

    quick question on a gasket kit

    anyone know the correct fel pro gasket kit for a 306 w/ tfs heads and gt 40 upper lower? i want to regasket my entire motor before i drop it into my notch. thanks!!
  12. M

    mass air harnesses

    i just bought an 86 notch and i'm converting it to efi. Now can i use a mass air harness out of a 91, or only out of an 89? I am pretty sure there are 2 plugs from a 91 harness that connect to 2 plugs from the dash harness, and that in 89 there is only 1 plug for each to get power to the...
  13. M

    Suspension guys come in!

    Looking for a good street/drag suspension that hooks. Not looking to spend major money for anything crazy, but the car is not a daily driver either. I already have UPR lower control arms, ET streets, and lakewood 50/50s to go in the rear...now someone share your knowledge to complete this set...
  14. M

    Anti roll bars

    can someone explain to me how they work, what it replaces, hows its installed...basically any information that is pertinent to know before getting one. I'm debating whether i just want to stay with the basic uca/lca set up or something a bit... plus i want to keep my tail pipes on my gt and i...
  15. M

    Thoughts on 10:1 plus S trim

    what are peoples thoughts on a 10:1 cp motor plus an S trim with about 7-8 psi, safe tune??? I know it can be done, how safe is it with a good tune? and would i be able to run 93 octane? thanks in advance.
  16. M

    anyone run 15x7 welds in the rear of their fox?

    if so what backspacing for 265/50 tires? car will have quadshocks removed. i was going to buy 15x8 but found used local 5 lug draglites with 15x7 and 5.5 bs....thanks in advance.
  17. M

    Anyone running 265/50/15s on the draglites???

    if so what backspacing do u have to make them fit under a fox? thanks in advance.
  18. M

    A few fuel line to mechanical pump questions--carbed guys help!!!

    i'm running a fuel cell, to a mechanical pump on the block, to a holley carb. Now the fuel pump has 2 lines the main and return. I do not have to use the return line correct? just the main line, and just plug off the return on the pump? if so what do i use to cover the fitting on the fuel pump...
  19. M

    Help--Neutral Safety issues

    ok, finished my conversion car....BUT, i can only start the car by jumping the solonoid and shut car off by ground out the positive battery terminal....ok hahaha-- anyway, car was oriiginally 4 cylinder auto, and no carbed 5.0 spd. But it looks like the neutral safety plug is different from...
  20. M

    anyone with a carbed 87-93 5.0 using MSD ignition module

    quick question, on the msd ignition module's magnetic pick up, there is a orange wire and a green wire. without using the extension/adaptor, if i splice right into the wires, which wires are they connected to on the vaccuum advance distributor wires? thanks in advance :)
Top Bottom
Back
Forums
Menu