Search results

  1. Beasty306GT

    Dcc 2 Speed Fan Controller

    has anyone had there 2 speed controller crap out on them..mine doesnt work anymore..was driving the other day and the fan wouldnt kick on..i checked the fan off the battery and it still works like it should..just curious..i ordered a new one but now i have to wait who knows how long for it to...
  2. Beasty306GT

    speedo cable

    i have been hearing a squeakin noise when im driving the car and im pretty sure its the speedo cable..it works fine and doenst jump at all..i was wondering is it possible to lube the inside of the cable with like wd40 or something like that to stop the noise?
  3. Beasty306GT

    ignition switch

    i need to replace my ignition switch on my 89....should i get a motorcraft one or can i go with a (Standard) is the brand from C A P .... what do u guys that replaced them prefer
  4. Beasty306GT

    lights dim???

    So tonight was the first time i drove my car at night and i noticed that when i turned my lights on they dimmed a bit and gauge dropped a lil bit ..i have a 3g 130 amp alternator and underdrive pullies on the alternator crank and water pump...would this have something to do with it? when i was...
  5. Beasty306GT

    vacuum

    so im trying to find the best place to get vacuum for my fuel pressure regulator i have trick flow track heat upper and lower intake...right now its hooked up to the block of plastic vacuum lines on the passanger side behind strut tower...i want to get rid of them..so where would you reccommend...
  6. Beasty306GT

    rms ?

    so i got my rear main seal today but what the heck is the plastic clear ring for that came with it? do i use ot or toss it?
  7. Beasty306GT

    fan

    so im converting to a electric fan and i dont want to use junkyard parts i found this one here Mustangs Unlimited - The Premier Source for Mustang, Shelby and Cougar Parts and Accessories has anyone had experience with this setup??? ..im also goin to install a 200 amp altenator...and if it...
  8. Beasty306GT

    name change

    If you would be so kind to change mine to Beasty306GT i would appreciate it
  9. Beasty306GT

    need help

    So i was driving last night to a car show the temp read 180 when driving...but then when i got into stop and go the temp started climbing to 210+..it didnt do this the whole time before even on the dyno it stayed under 190 thw whole time...but i recently changed my heater core could that have...
  10. Beasty306GT

    heater core

    So when i had the car on the dyno my heater core decided to spring a leak...So now i need to replace it..i know mosty everyone pulls the whole dash...but i was looking at the haynes manual...it says the whole heater case can be removed without taking the dash out...has anyone done it this...
  11. Beasty306GT

    tune

    so i want to get my new motor dyno tuned..everything is new..what do you guys recommend for miles on the motor before i get one
  12. Beasty306GT

    what I have been doing all winter

    So finally today me and my buddy got the car running today...i have been workin in it since last september ...its a built 306 svo aluminum heads...not sure on the cam i know its 530 lift..heads ported and polished ...trick flow fuel system..upper and lower intake also trick flow..accufab 75mm tb...
  13. Beasty306GT

    fuel question

    so im getting ready to hook up the fuel lines to the motor..but while i was workin in the engine bay i kinked the nylon fuel lines on the passenger side right where they connect to the hard lines question is can i use the 3/8 rubber fuel line to replace them with hose clamps?? i replaced the...
  14. Beasty306GT

    gauge

    so i got a electric water temp gauge my question is can i use a port in the back of the lower intake for the sending unit or should i install it in the front where the stock one is? i want both gauges to work ...so would it be the same temp in the front and back?
  15. Beasty306GT

    plugs

    Does anyone know what spark plugs to run on the f3zm6049 y302 svo aluminum heads..any help would be appreciated i want to use motorcraft
  16. Beasty306GT

    heads

    Does anyone know what size studs and roller rockers i need for SVO gt 40 aluminum heads? i was wonder what my options are i just dont know what size stud i need.. :shrug:
  17. Beasty306GT

    mounts

    does anyone know what size nut i need for motor mounts to k member .. i got energy suspension i threw out my old k member with the old mounts on it..any help would be appreciated..
  18. Beasty306GT

    motor mount

    I have energy suspension motor mounts and i was wondering if anyone knows what size the nut to k member? i tried all sizes and i couldnt find it ..thanxs
  19. Beasty306GT

    wheel question

    Ok so i changed my whole front suspension and now i was wondering i have 9" wide wheels they fit before i changed it all..So now i got coil overs.so my question is to any of the guys with coil overs what size wheel do u have and what will it take to fit..im trying to find out before i try to...
  20. Beasty306GT

    new setup

    So this is a project i been workin on for months now..finally got it pretty much together :D And this is before
Top Bottom
Back
Forums
Menu