Search results

  1. H

    4 link rear floor suggestions for hump please

  2. H

    New coil sag?

    I'm putting a new set of coil springs on my '72 and will most likely be cutting them to get the stance right. How quickly (and how much) do new springs sag, or do they? I don't want to cut them and have them settle 2 more inches a week later. That would be a drag. THANKS! Mike
  3. H

    '67 Glove latch and catch

    anyone know where I can get a couple of these for my project? Thanks!
  4. H

    65 AC and PS bracket set up

    Can anyone point me to pictures, or e-mail them to me of the mounting brackets and pulley set up for a 65 with a 289 (68 or later), AC and PS please? This issue is we aren't sure if we have the right water pump, or brackets, but we can't get the AC and PS bolted up. My e-mail is...
  5. H

    WTB C-6 parts 71-73 Stang

    need the rod from the shifter to trans, the lever that goes on trans shaft and rod to column lock. Email me at [email protected] with what you have. Thanks!
  6. H

    Trunk bumpers on '67?

    Does the '67 have bumpers to set the trunk height? I cut the car apart a couple years ago and there are a couple holes in the outer corners that looks like it should have bumpers or something in them. Anyone have a pic of their '67 trunk area they can post please? Thanks!
  7. H

    Eleanor side rocker panel bolt on

    My Eleanor project has a couple twists and I am doing it as a "bolt on", but I do have a fairly basic question here for anyone knowledgable on Eleanors. . My twists: 1- Steel hood. I needed a taller scoop to clear carb inlet from supercharger (D1-X on 472). I also added hood vents, 2-...
  8. H

    anyone recognize this e-brake cover?

    I pulled this off what I think is a 5.0, but don't know the year. I need the felt piece that seals water and need the year to look for it. Thanks!
  9. H

    68 Shelby hood vents

    does anyone have any idea where I can get just the louver/vents or something similar? THANKS!
  10. H

    Bad brake caliper in my 72?

    I'm not sure what is wrong, but my pedal is soft. I've bleed a few times, new fluid, etc. and still soft. When I put it on the road, I used a residual valve recommended by MP Brakes for the front discs. A couple miles down the road, the passenger caliper locked. When I loosened the bleeder...
  11. H

    another wheel stud / lug question

    anyone know where I can get longer front and rear wheel studs? My local parts places are useless. I know they are 1/2-20 but can't get correct knerl/shoulder information. Thanks!
  12. H

    Tall tires

    anyone know if you can run a 28" tall tire on a 71-73? A 30"? Thanks!
  13. H

    Sticky float on 850 DP?

    Sorry for an amateur hour question, but... I've been fighting 5 weekends with my Holley 850 DP and I read all the symptoms as a sticky float, but..... The car was running fine (maybe 10 miles on it), when, in the garage fortunately, demons possessed it or something, Here is what...
  14. H

    A nice gold recommendation for my '67

    anyone know of a nice, lighter gold body paint I could use with some black accents (maybe hood) for my '67 Eleanor-ish clone? I saw some nice '72 colors, but was hoping for a newer car so I could see what it looks like. THANKS!
  15. H

    71-73 C6 cooling line ?

    Can any 71-73 folks tell me if and where the cooling lines are clamped to the car underneath. Pics would be great, but telling me would be helpful. THANKS!
  16. H

    Liquid masking tape

    has anyone ever used any type of a liquid masking tape to paint interior pieces like the dash? What did you use and how did it work? THANKS!
  17. H

    Interior lights voltage ? (71-73)

    I have 12v on battery, ignition and yellow in to headlight switch. I drop to 11v (max turn to left) or a bit less on interior light feed (lt blue). Probably not a big deal, but is this right and any idea why its doing this if not right? I do have a new headlight switch FYI. THANKS!
  18. H

    71-73 shift rod stud

    anyone know where I can find one of these? This is the stud (bolt type thing) that you use to adjust the shifter position to the transmission. THANKS!
  19. H

    Printed circuit repair

    Can anyone recommend a glue or way to attach the copper back to the plastic in my 72 instrument panel (printed circuit board)? 3 of the copper things are seperated and I'm not getting a reliable ground for the cluster lights. Thanks for any help!
  20. H

    Power windows 71-73

    Any suggestions on finding window tracks and motors I can use to convert my manual windows to power in my '72 vert? I can't find aftermarket that will work and haven't lucked into a parts car. Are Cougar or any other cars the same or anyone have a suggestion? THANKS.
Top Bottom
Back
Forums
Menu