Search results

  1. 89stangalang

    Windshield Wiper problem

    I was driving today and suddenly my windshield wipers started going real slow and gerky and now they arent moving at all. Would this most likely be caused by the switch or the motor?
  2. 89stangalang

    Vibration help please...

    I have recently started to get vibration in my drivetrain. It has gotten to the point that I can see my shifter even vibrating....scary.... Is this likely a driveshaft or U-joint problem? Or is it the transmission itself? It basically vibrates under load (acceleration) or when cruising at...
  3. 89stangalang

    Engine running like crap...pulled codes.

    My engine started running like crap today and it pulled these codes... 31o : EVP or PFE circuit below min voltage. 41c : HEGO(H02s) sensor voltage low/system lean. 66c : VAF/mass air flow sensor fault, below min voltage OR... TOT sensor signal input below self-test min, or vane air flow...
  4. 89stangalang

    Anyone have this Gauge Pod?

    http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=7990917764&ssPageName=STRK:MEWA:IT I have never seen one before on an actual car. I love the idea of moving the cd player up and still getting a good view of your aftermarket gauges. The asking price seems too steep though...
  5. 89stangalang

    Smog Pump Questions

    I have recently added a new discharge tube and mini race bypass valve to my car and the smog pump lines are directly in my way. Is there any way that I can just cap off the lines and leave the smog pump there, but have it do nothing. If this can be done what would i have to do to the vacumm...
  6. 89stangalang

    check engine light on questions?

    I have the code reader and it pulled two codes from my 89gt mustang. The codes were 31 C and 31 O. Both of these codes mean EVP or PFE circuit below minimum voltage. What problems could this cause and how can I go about fixing the problem? Also I discovered that one of my vacuum lines has...
  7. 89stangalang

    Need to get a Dyno Tune.

    I have recently just finished installing my vortech supercharger and I am looking for a good shop in my area to get a dyno tune. I want to get the chip burned right at the shop. Is there anything in the Spokane area. I am willing to travel some if I have to. Any help would be great.
  8. 89stangalang

    Need some help!!!

    Ok i was driving to work yesterday and the car started to sputter some and then made like a banging noise from the engine. I then stopped it at work and left it there for a few hours. I went back and the car is running fine again but the check engine light came on. It pulled 31 O and 31 C...
  9. 89stangalang

    Need Help!!!

    Ok my friend has a 94 v6 mustang. His mustang was not charging properly so we had the alternator checked out at Shucks and they said it was bad. So we picked up a new alternator for the car and everything seemed to work fine after we jump started it. Now a few hours later we started driving...
  10. 89stangalang

    BTM took a crap on me???

    I just finished changing over my MSD 6AL ignition set-up to a BTM that is also an Ignition. I finished the swap and the BTM/Ignition was working perfectly. I then closed shop for the day and went back to start the car the next day. The car will not Idle at all now and sounds like the biggest...
  11. 89stangalang

    MSD BTM rev-control how to?

    I just installed my used MSD BTM that came with my supercharger and I would like to know how to set the soft touch rev-limiter? Right now it is set at about 4100 rpm.
  12. 89stangalang

    MSD 6AL and BTM

    Can I use both of them at once or can i only use one of them. I currently have the 6AL installed in my car. I need the BTM for my new supercharged setup. What should i do?
Top Bottom
Back
Forums
Menu