Search results

  1. L

    2013 Fusion Se Erratic Turn Signal

    My gf bought a brand new Fusion last year and it's spent more time in the dealership for issues then she has actually driven it. Like always the dealership can't figure it out, so I'm hoping someone on here might have some insight or have gone through this and had it properly fixed. The left...
  2. L

    Power??

    Hey everyone, I'm looking for some opinions on what you guys think I might be pushing for power numbers. My car is just about complete with everything listed in my signature, right now I have just been finishing buttoning up all the connections and what not with putting in the new motor...
  3. L

    Cylinder Head CC's

    Hey everyone, I have a set of heads that one of the heads combustion chamber is one (1) cc lower than the other head. When the heads are bolted onto the motor would this difference create any problems? Thanks for any input.
  4. L

    MM K member

    Hey everyone, I'm looking into ordering a MM K member set up and I just have a quick question. Does anyone on here have the MM k member kit with the stock geometry arms and 17" Rims? I'm curious as to if the 3/4" forward movement will cause the wheels to rub. I did a search but didn't come up...
  5. L

    Piston Valve Reliefs

    Hey everyone, Is there any way to either look or measure the valve reliefs to determine how large of a valve will fit? Thanks,
  6. L

    Cylinder Head Issue....

    Hey everyone, I had my heads standing up and one head fell over; when the head hit the cement floor it put a chip in the bottom machined surface area. The chip at the widest point is 1/4 inch and starts in the combustion area then extends towards the outside (exhaust side) approximately a 1/4...
  7. L

    Vert Top Frame

    Hey everyone, On my vert when I put up the top it is a complete struggle to get the latches to line up, and once the top is finally locked down there is a pretty good gap between the top and windshield frame on the corners. Is there anyway to adjust the frame other then just unscrewing the...
  8. L

    T-5 Input

    Hey everyone, I'm on a budget build and I have a 4cyl T-5, to make this thing at least some what stronger until I can afford a tremec or somthing of the sort can I use an Input shaft from a 5.0 t-5 or would I end up having to swap out the entire gear set? I believe that all the 4cyl t-5's...
  9. L

    1/4 mile

    Hey everyone looking for an estimate on what my car should run once I finish putting it together. 90 Lx Vert 5.0 302 Bored .030 9.5:1 c/r Stock heads ported with GT40 valve package E303 Cam 1.6 Full Roller Stud mount rockers Cobra Intake 65mm throttle body 24 lb/hr injectors 76mm...
  10. L

    Choosing an Intake???

    Hey everyone, In the process of building a motor and I'm looking for recomendations on what intake to buy. The car is used for street/strip Here is what I have: 302 bored .040 9.5:1 Compression E7 Heads flow bench ported with Gt40 Valve package Ford E303 Cam 1.6 rockers 5spd with...
  11. L

    302 - 306

    Hey everyone, The 302 started began to get tired so I brought the motor into the machine shop for a simple hone, clean and all new bearings, well they told me that one piston was cracked and the cylinders were going to need a bore. The shop is ordering pistons and boring it 30 over, I'm...
  12. L

    Will not idle

    Need some help, recently my car started having trouble idling when it was cold. When I start the car cold it will not idle, i have to hold my foot on the gas for a good minute or 2 before it will finally idle on its own. I have tried just putting it in gear and driving before it will idle on its...
  13. L

    STARTING HELP!!!

    Hey guys So today I just finished converting my car from Auto to 5spd. When i went to start my car to take it for a test drive, as soon as i put the key in the ignition and turn it to the point were only the dash lights should come on along with the radio the starter engages and the car will...
  14. L

    Looking for some opinions on a tranny

    Hey guys I just went through my second aod this time it was a Lentech Street terminator that the planatery gear set shattered and cracked the case. Im sick of aod's so I have been thinking of converting my car over to 5spd, rather then goin with a c4 or something just because i like to have the...
  15. L

    Pushrod question

    Hey guys I just bought pushrod guideplates and on the package it says to use heat treated pushrods. My motor has stock push rods can I use them with the guideplates?
  16. L

    Idling problem

    Hey guys, I have a slight problem, when i start my car up it will idle at about 700 rpms, after driving the car for a couple minutes then stopping at a light for say, it will idle at 1500 rpms, but if i turn the car off then right back on the idle will be right at 700 again. Im so lost on...
Top Bottom
Back
Forums
Menu