Search results

  1. M

    67 coupe weight/ linear coilover spring rate

    Hey guys, im jsut about to order a set of coil overs, QA1 aluma matics to be exact and needed to know what my rear weight may be, However i never got a chance to weigh the car before i started restoring it, and tore everything apart. Its a 67 coupe, no ac, no power sterring, no power...
  2. M

    Front springs

    Hey guys, ive got a 67 coupe and it has 428 big block springs in it... Im putting a small block in (289,302 block). Should i replace them with something like a 620 or take the springs and cut them down to my desired ride hight? If i do cut them down how would it handle, shift weight and all...
  3. M

    Wear safety googles!!

    unfortunately i dont wear them as much as i should but im going to now. Somehow 2 days ago a peice of metal got stuck in my eye in the bottom part of my iris. I didnt notice for the first day and went to sleep with it. As most people know while you sleep you go in and out of REM sleep...
  4. M

    Mustang symbol antarshia, kinda diffrent

    Hey guys, in wood shop at my school we had to make antarshia's( Kinda a multilevel wood picture deal) so i decided to draw up a mustang symbol and make my antrashia that. I actualy made two of these and gave one to a friend for letting him barrow some tools while i work on my mustang. He got...
  5. M

    Half back ladderbar/coilover

    Hey guys this is what i have so far, take a look, any feedback would be great.. Really want to knwo what you guys think before i mount it all onto the car. The rods in place of the coilovers are not perminent, they are jsut for rolling the car in and out of the garage, until i buy some 14"...
  6. M

    Rear wheel wells

    Hey everyone, was wondering how these were connected, the inner and outter wheel well that is. I looks like some kind of crip along the whole thing. Anyways how do you remove them? can you heat them up or is it jsut alot of cutting?
  7. M

    lead work

    Hey everyone, im about to replace a full quarter panel on a 67 stang, coupe. Im Debating on cutting lower than the lead and meshing the metal, but would almost rather redo the lead, anyone got any tips or experiences with it? Thanks
  8. M

    Anyone buy anything from Rustrepair?

    Im looking at getting a quarter panel from them but wasnt sure what to expect, anyone get anything from them? www.rustrepair.com
  9. M

    anyone got this pic?

    Anyone got a pic with a 67 coupe without rocker moldings? trying to figure out if i like the car without them or with them. Thanks Guys!
  10. M

    Swap meet

    Any of us older stang guys heading to the Portland, Or big arse swap meet? There is ussualy a ton of good deals and plenty of selection, takes up the whole expo center and the parking lot and you park at PIR :D (which you may be able to sneak a lap or two in, if you are daring enough and...
  11. M

    pics of 4 link thus far

    Hey guys, got some of the brakets made, but ran into a delima... I was orrigonaly planning on welding the brackets to the axle housing, however have been thinking this may cause binding and such in the coil overs and suspension. Was wondering if i have to make this a floating housing or if...
  12. M

    4 link system rod ends

    Hey guys, i was wondering if a Heim Joint/Rod End 1/2" with Ultimate Radial Static Load Capacity of 8386 would be strong enough for a max of 350-450 ft-lb of tourque the 4 link is gonna be on a 67 mustang about 2500 pounds, but that was with a 428 cj, so with the 302 it will be alittle less...
  13. M

    Rear independent suspension

    Hey guys, ive been sketching out some ideas and was wondering if this one looked fesible as well as durable. I sketched this one very quickly while looking under the car so things may seem out of porportion and such, so any questions or advice on the sketches would be appriciated. Thanks...
  14. M

    Rear leaf spring moving

    Rear leaf spring moving, fuel cell, bunch of q's Hey guys, was wondering if theres anyway to switch the leaf springs to the other side of the frame rails, and then making a breaket for the back pivot point... Dont know if this has ever been done or not but im trying to get alittle more room...
  15. M

    Suspension boots, bearings, bushings

    Hey guys, im in need of replacement of all the bushing, ball bearing boots and everything in my suspension, Im trying to stay in a budget right now though. Where do you guys recomend getting the parts(online stores preferably)? links and parts numbers always help. Thanks in advance guys!
  16. M

    Cowl resto

    Its about that time that i need to start on the cowl :bang: , stripping, patching, and painting. So my question is, what are some of the methods out there that you guys use to do these 3 steps?
  17. M

    67 coupe resto planning (motor, trans)

    Hi, im currently in the process of a slow restoration of a 67 mustang coupe, and am now planning for the summer on a transmission and motor comb I will want to try and drop in. I am 18 and currently still in high school which leaves me with plenty of time and little money, but with the summer...
Top Bottom
Back
Forums
Menu