Search results

  1. white_97_GT

    90 Lx Falling Flat On Its Face...help

    i re built my 302 into a 331 over the last couple of years, finally got it running this spring. it was running great for a month or so, then started acting up all of a sudden. once it has been running for a while, it will bog down and not have any throttle response unless i floor it. if i...
  2. white_97_GT

    Can't read A9L with scantool...help

    here goes, i have a 90 lx, in the past we tried using a scan tool to figure out some codes and other issues (a good friend of mine is a licenced mechanic and has all the fancy gadgets) but could not get anything on the tool. seems the connector isnt working. have any of you heard of this...
  3. white_97_GT

    New Engine running too cool

    hey guys, i just finished building a 331 for my 90 lx, it doesnt want to get up to opperating temp. guage reads no higher then 140-150 degrees even after long city drives. i already tried replacing the thermostat (tested both the new one and the old one, both work fine and didnt fix the...
  4. white_97_GT

    mounting an MSD box in the interior

    where have you guys mounted your MSD boxes? i would rather not mount it in the engine bay because i know a lot of guys who have fried them from water. i cant find a good spot inside to mount it...ideas? pics?
  5. white_97_GT

    constant shift light

    hooked up my proform tach and shift light today. problem is the shift light lights up and stays on at al times, when i hit the shift point, it gets brighter, and still stays on. we're thinking it has something to do with connecting the green wire to the neg side of the STOCK coil...any help...
  6. white_97_GT

    Help moving the HVAC Controls

    so im in the process of moving my HVAC controls to the bottom of the center stack, however the vacum lines for the selector (defrost, a/c, floor, vent...etc) are too short to get down there, how have you guys who have done this got around this problem?
  7. white_97_GT

    header gaskets?

    im in need of a part number for header gaskets for gt-40 heads (non ported) and 1 5/8 headers, thanks
  8. white_97_GT

    whats wrong with my t-5?

    took my 90 lx to the track on the weekend, when i tried to shift into 2nd at anything over 4000 rpms it wouldnt go in, i figure its the syncros, anyone else have any ideas? its a stock t-5, the car has a cobra intake, gt-40 heads, b 303 cam, 24# inj, 73mm maf, 65mm tb and long tubes, soon to...
  9. white_97_GT

    fuel injector issue

    ok guys, im not sure if this will be an issue or not, but the plastic piece (looks like a hat) on the end of one of my 24# ers is cracked, will it still work properly, or do i need a new injector
  10. white_97_GT

    lifter opinions

    ok, i used search, got tired of reading something different in every post, so heres my question: i doing my top end, gt-40 heads and a B cam, engine has roughly 60-70 K on it, new cam is used, about 2500 miles, will my stck lefters be ok? i didnt have any problems with them when i tore the...
  11. white_97_GT

    changing motor mounts...help

    ok, im trying to change my motor mounts, but i cant get the big nuts that bolt the mounts to the k member off, any ideas???
  12. white_97_GT

    propper backspacing?

    im looking for some draglites for my fox, im not sure what backspacing will work, any ideas, or maybe some pics of different spacings??? thanks guys
  13. white_97_GT

    combo question

    ok guys, ive got a question here about a possible combo, its for my dad's 94 gt, the car already has a cam (seems like a 'b' cam or similar), full length headers, 2.5" h-pipe with high flow cats, 2 chamber flowmasters and a 3.73 gear, i dont think the stock intake is working very well with the...
  14. white_97_GT

    engine build questions

    ok engine guys, im getting ready to tear into my engine, im putting gt-40 heads, cobra upper and lower intake and a new cam (plus all the other bolt on stuff that goes with it, injectors, tb, maf...etc) im not planning on re-building the sortblock unless i have to, my question is, do i need to...
  15. white_97_GT

    rim ideas???? pics inside

    ok guys, i dont know what rims to go with, im on the fence on the race look or the street look, if i go race it will be draglites for sure, if i go street, i have no clue, id like to stick with something that originaly came on a mustang...any ideas??? ive also considered painting the black on...
  16. white_97_GT

    check engine light trouble

    my engine light comes on once the car is warmed up, like say after i get off the highway and im goin down a normal road, it comes on, any ideas?? o2 sensor?
  17. white_97_GT

    what cam is best?

    ok, i know this is a newb question, and i tried searching already, there is just too much stuff to read through to find the answer...im planning on picking up a few parts from a local guy, all used, gt40 heads (complete iron heads) with upgraded springs (he says good to .500 lift) and 1.6 fms...
  18. white_97_GT

    rear ctrl arms, spherical or poly, adjustable or not?????

    looking into some rear control arms, uppers and lowers, what are the pros and cons of spherical or poly bushings, and adjustable as opposed to non adjustable uppers????????
  19. white_97_GT

    wheel spacers?????

    ok guys, i wanna get the rear wheels out a little farther on my dad's 94 gt, hes got cobra r's (stock width) i need to know how thick of a spacer i can use with the stock lugs????? also if anyone has any pics of their spacers that would help to since i plan on making them myself, thanks
  20. white_97_GT

    flowtech headers

    anyone have issues or good things to say about flowtech headers for 5.0L? im looking at the ceramic coated long tubes from summit, same price as bbk chrome
Top Bottom
Back
Forums
Menu