Search results

  1. RedBullitt

    valve spring suggestions

    im gonna be running a low compression mmr 900 sb with vt 3 blower cams (.545/.545 lift, 238/242 @50, 115 lsa). Stock stroke/bore. Stock 2 valve heads for now, going to use kb2.6 and around 15 psi. What valve spring would you reccomend?
  2. RedBullitt

    vt or crower

    anyone have sound clips or experience with vt 3 supercharger grind or the crower 3 supercharger grind?
  3. RedBullitt

    Cams,shortblock,kenne

    hey all, i finally ordered my shortblock today, mmr 900 with windage tray, arp main studs, good oil pum, and notched 17cc low compression pistons!! ---> now for some good blower cams. Suggestions please... I was looking at the crower stage 3 supercharged, i dont think they would help me...
  4. RedBullitt

    help, engine...

    hey everybody Its almost time to get some serious ass under the hood. I will have a little more than 10k to spend. Suggestions would be great... i am looking at a modular mustang racing 950 short block topped with a kb 2.6; out of curiosity,i have a noszle kit in the garage, could it work...
  5. RedBullitt

    snow methanol

    hey everyone what is the difference between the snow stage 1 injection kit and the stage 2 kit? also, would there be significant gains with 14 psi kb? safe? can it be used WITH an intercooler? how is the install? thanks
  6. RedBullitt

    Gears and no calibration

    Hey everyone I have 410 gears installed and my speedo is set for them. thing is i am going to sell my predator (had a custom tune with it for everything) before i get my kenne bell and tune this spring :flag: . Will there be any adverse effects from running the car without the tuner, just in...
  7. RedBullitt

    injectors

    hey do the injectors from brand new stangs fit 99-04 models?
  8. RedBullitt

    pro stars

    hey all Im looking into getting a set of weld prostars for my rears for some slicks... how wide can i go? oh i am also getting mm lcas, so that might make a difference with the quad shocks. i was hoping on 12 inch wides, but i dunno lol, any way to get those under there? also, what...
  9. RedBullitt

    mmr block

    looking into a mmr short block, it says it is a new cobra block, will my current headers bolt up or not?
  10. RedBullitt

    New Block

    hey all i am looking into getting something tougher for the bottom end of my motor. I have seen several mark viii blocks/motors for reasonible prices. I was wondering how difficult this would be to use with forged internals; possibly bored 20 or 30 over. would there be anything very difficult...
  11. RedBullitt

    4v internals

    what are the internals like in an 01 cobra motor? are they glass like the gt or are they stouter?
  12. RedBullitt

    power window issue

    ok heres the trouble, my sister has a 99 buick century, her rear power window seems to be totally dead. the switch will not move the window, and if it is pushed up she says it will fall back down with some driving. any idea what this could be? i figure all these are just about the same in most...
  13. RedBullitt

    fattttt air/fuel ratio

    alright all.... here we go. i have my wideband installed just a little bit ahead of the cat on the drivers side. it seems to be working alright, it takes like 20 seconds to warm up, then it reads about 10.4-10.9. when running it will jump up to 10.9 and a back down. at idle it will fluctuate...
  14. RedBullitt

    bolt ons porting nitrous ---> injectors?

    hello all, i have my gt with all the stuff in the sig, in the near future i am going to be running a 125 shot with the direct port noszle kit. also i am going to add in the near future a set of very ported heads, maybe a VT stage 2 or nitrous cam. maybe some more after that. my question is...
  15. RedBullitt

    air fuel ratio na and nitrous injected

    what would my best af ratio be right now running NA without the spray? i have my wideband in there as of tonight and i was just curious what i should run it at. how about with a 125 shot via a noszle direct port kit? thanks just trying not to break too much haha:SNSign:
  16. RedBullitt

    behind gauges wiring

    hey all which color wire behind the gauges on an 01 gt is the one they get there power from? are there 2 different ones? i am hooking up a wideband 02 sensor, so i need to find a wire to tap into to power the gauge and a wire to power the controller. would i be able to use the same wire for...
  17. RedBullitt

    shudder??

    hey all, i think i have something funky going on in my drive line. at least thats what it feels like. in every gear, if i get up to a decent speed and let off then put the pedal down with some ass or quick i get almost like a shudder, jerking thing going on for a second or 2 then it goes like...
  18. RedBullitt

    new CEL?

    hey all, confused.... im throwing the cel, just put headers on. no leaks. i scanned the codes, none come up. i clear them then later the light comes back. howcome lol? any ideas would be appreciated.
  19. RedBullitt

    cams and kenne bell?

    hey all what would happen if i slapped on a kenne bell right now, with my cams etc lol? yes i know they make blower cams, but for the sake of speculation and my lazy arse not wanting to mess with them lol. i was thinking i would have a rather hard time making boost lol, any thoughts?
  20. RedBullitt

    porting PI heads

    how good would the benifits be on a 01 gt with ported heads? NA and FI (maybe 6 lb kb)? Neighbor wants 1100 dollars for a pair of ported and polished 2003 gt heads. he said 5 angle valve, comp cams springs, ferea valves. already have cams, are they worth it? or should i just save that money...
Top Bottom
Back
Forums
Menu