Search results

  1. N

    Lifter/Rocker Question

    can you use the lifters/rockers from NPI heads on PI heads?
  2. N

    Rear Brake Help

    I did my rear brakes yesterday and something is not right. 1st off the bleeder screw broke off of the right passenger side calliper :mad: . And the drivers side caliper smells a little bit and inside the wheel well is very hot after a drive. I thought that maybe the calliper was messed up on...
  3. N

    RPM'S Are Pissin Me Off

    Ok, whenever I push in the clutch my RPM'S stay at 2000 and wont drop. If they are lower than that, such as me letting the RPM's get low before I push in the clutch, they will climb back up to 2000. I don't know wtf is going on. I changed the tps sensor and the iac a couple months back...
  4. N

    RPM Questions

    Hey guys I'm having a hard time fixing a rpm problem. What happens is that when I'm driving down the road I will push the clutch in and the rpm's will drop down to 1500 and hang at that position until I come to a complete stop, then they drop down to idle. I have recently replaced the IAC...
  5. N

    ???Clutch Question???

    Ok guys/gals, I think the clutch is starting to go. I hear a high pitched noise when I'm at low rpms and sometimes idle. Is that the throw out bearing? And when the noise became apparant to me I would push in the clutch while driving and the rpms wont drop past 1200 rpms. Now sometimes when...
  6. N

    Video Request

    Does anyone have the video of the PI Swapped GT racing a TA? Thanks if you do and could post the site or video.
  7. N

    Video Request

    Sorry Double Post
  8. N

    Starting Problem

    Ok guys, lately when I go to start my car it will rev. up to like 1200rpms and then die. I have to push the gas to keep it from killing itself. Some times it takes three times to get it started and idle and other times it takes twenty. Then when it idles i will rev. it a little and the rpms...
  9. N

    ???Autometer Electric Water Temp Gauge???

    Ok, I have an autometer Electric water temp. gauge and I am having a hard time with it working right. I have the sender tapped into the thermostat housing piece and it is reading 250*. when the engine is cold it starts low and climbs all the way up. I have no idea what the problem is. Can...
  10. N

    Mach1 Shocks/Struts

    I want to put these on my stang, I have frpp C-springs, but I cant find where to get the Mach1 Shocks/Struts. Any help would be appreciated.
  11. N

    Its ALIVE!!!

    Well the last 5 days have been grueling. I finally got PI cams and Intake Manifold on my NPI. It took so long because my Dad had to have eye surgery, so I have had to take care of him and the last 4 days I have had to work:rolleyes: . But its finally done, I used the AFM cam tool and had no...
  12. N

    Well it finally cracked

    My NPI intake finally cracked, right by the thermostat. I have a PI intake manifold that I have been wanting to put on so this gives me the opportunity. Am I missing any parts for the swap from this list, PI intake manifold gasket, RTV, PI coolant tube, and the PI intake manifold? Am I...
  13. N

    Stock Cam Question

    Do the 98 GT's have the bolt on or pressed cam gear?
  14. N

    ??? Mac Prochamber ???

    Hey guys I just started thinking today about what my prochamber looks like and the one in the pics by the dealer. My prochamber was 5 pieces, two pipes coming down from the headers and two pipes connecting the header pipes to the H section. Could they be using a new design so shorty headers or...
  15. N

    PI Cam & Intake Manifold #'s

    What kinda horsepower gain do you see with just the cam and intake manifold swap? And how much higher does it pull up top? I have the intake manifold and I had PI heads but sold them because I want to eventually supercharge it. Will it bring me close to what a 99-04 has?
  16. N

    bLiNkEr

    I know this sounds stupid but my right blinker is faster than the left. It makes a faster ticking noise and blinks faster. Any ideas on what the problem is?
  17. N

    Mac Prochamber Install

    Well I'm putting the Prochamber in today...:D I woke up this morning and took the factory H-Pipe off and I also took the factory Tranny mount off because I am replacing that piece of *****. That mount was really beat up. My H-Pipe arrives this afternoon so right now all I can do is wait...
  18. N

    Valve Chatter

    Hey guys, Whenever I am driving and I give it a little gas I hear a chattering noise coming from the top of my engine. When I use 91 octane it almost disappears completely. Whats the problem? Could my timing be off, and would a Steeda Timing Adjuster fix it? Any help would be appreciated.
  19. N

    Headswap Tune

    Ok guys, I was wondering what kinda tune you guys have with your headswap. Would a diablo be able to tune it? Or should I get a dyno tune? any input is welcome. thanks
  20. N

    Part #

    I have a pair of PI heads and I am missing a bolt on one of the camshaft caps. Does anyone know the part number by chance. I would appreciate it! Thanks:nice: Oh, and what has everyone been paying for these parts for the headswap. YF7Z-6279-AA Cam Sprocket Bolts (2req.) 1R3Z-9424-AAA...
Top Bottom
Back
Forums
Menu