Search results

  1. 89gt89

    How to re-install a t5 cover plate??

    I just bought a t5 and I wanted to make sure the gears look ok. They look great. However, I removed the cover plate and can't find out how to put it back on right...I can get it back on but I can't shift thru the gears. Any ideas? Thanks
  2. 89gt89

    Accufab Adjustable Fuel Pressure Regulator

    Nice FPR. 60- Free shipping from 98012
  3. 89gt89

    79 - 93 Smog Pump Delete

    I switched to a shorter belt rather than use the delete. 60- Free shipping via USPS from 98012
  4. 89gt89

    C&L 73mm MAF plus 19lb Sensor

    C&L 73mm 19lb Meter. 90- Free shipping via USPS from 98012
  5. 89gt89

    Ranger 2.3 5 speed input shaft Q

    Hi Everyone, I just bought a 95 3.8 T5 that has less than 200 miles on a complete rebuild. I understand that a new input shaft is required to fit my 89 5.0. Either a 5.0 or a 2.3 shaft will work with the exception of a throw out bearing for the 4cyl unit. Does anyone know if an input shaft...
  6. 89gt89

    Injector Harness Rehab LSC, Cougar, T-Bird, 5.0

    Hi Everyone, I'm not sure if this topic has been discussed but here we go. I have an 86 Saleen that had a very tired injector harness. Cracked wire, exposed copper, disintegrated looms, busted connectors etc. I went to the local Pull A Part to see what I could find. 5.0 Mustangs are few...
  7. 89gt89

    SN95 Disc Brakes...Gutted SVO Proportining Valve?

    I installed SN95 front and rear discs on my SVO. I have an SVO Prop Valve that has been gutted and plugged. The front L and R lines are in the stock position and the rear brake line runs from the rear of the prop valve to a Wilwood adjustable prop valve. I've researched all the 3-2 port threads...
  8. 89gt89

    Gutted 94 Proportining Valve?

    Gutted SVO Proportining Valve? I have an SVO Prop Valve that has been gutted and plugged. The front L and R lines are in the stock position and the rear brake line runs from the rear of the prop valve to a Wilwood adjustable prop valve. I've researched all the 3-2 port threads as well as...
  9. 89gt89

    87-93 5.0 Headlight Harness??

    Does anyone know if there is a difference between 87-93 5.0 headlight harnesses? Got a 91 in need of a new alternator/headlight harness and need to check compatability. Thanks
  10. 89gt89

    Hub Centric Ring Measurements for SN95 Rear Disc Conversion

    You will need to get a hub centric ring if using Ranger/Aerostar axles when doing an SN95 rear disc conversion. Here are the dimensions for the ring if you don't want to spend $25.95 on a set of these Brake Rotors Drilled and Slotted,Hawk Performance Brake Pads,Car Brakes,Brake Drums,Cobra...
  11. 89gt89

    North RaceCars SN 95 Rear Disc Conversion

    Hi Everyone, Today I installed SN95 rear discs on my 91 Notch project. I started out with an SVO/LSC rear disc setup. The axle was out of an 88 Turbo Coupe with 3:73's. That setup was great for the 87 Saleen rims I have but I'm going to put them on my 91 hatch. The 89 5 star Saleen rims...
  12. 89gt89

    Lincoln VII AOD Trans Swap in 91 5.0

    Hi Everyone, Well I'm all done w/my 2.3 to 5.0 swap. The donor engine and AOD came from a low mile 89 LSC while all the other bits and pieces came from an 89 GT (minus motor and trans). I knew the transmission was going to be about 1" longer and figured that would be the extent of the...
  13. 89gt89

    Cylinder Balance test w/code reader problem......

    I just tried tried running a cylinder balance test with a code reader on my 91 5.0 and the engine shuts down when I press the test button.....Anyone ever have this problem before and what do I do to make this think work?
  14. 89gt89

    Low mile 1996 351W cam question??

    Ok guys, I have a very tired 89 5.0 motor that is in need of a swap. I bought a low mile 96 351W roller longblock out of a totalled Bronco. I pulled the heads for a cleaning and everything there looks great. I'm pulling the crank to replace the races on the main caps. The stock cam looks...
Top Bottom
Back
Forums
Menu