Search results

  1. 66mustangg

    Replace Rear Frame Rail and torque box

    I need to replace the drives side rear Frame Rail and torque box on my 69 mustang. Can anyone give me any pointers/ advice / tips or just walk me through the process. Thanks
  2. 66mustangg

    swap help

    In my 69 mustang i am swapping from a 6cyl to a 351. I went to put the engine in yesterday and it was sitting way to high. I used regular motor mounts from mustangs Unltd. Is there any other place where i can get different motor mounts to have the engine sit lower?
  3. 66mustangg

    coils

    I have a 69 mustang and im putting 1" lowered springs in the front. Do i have to relocate the upper control arm if i am doing this. some people are telling me to and some say you don't have to.
  4. 66mustangg

    distributor

    I have a 351 Clevland 2bbl that i am puttin into my 69. i just got the engine rebuilt and now i have to put the distributor in. I am a little confused about putting it in because there wasnt one in there already that i could go by. Any help appreciated Thanks
  5. 66mustangg

    Flywheel

    im swapping a 351Clevland into my 69 mustang which has a I6 with the original 3 spd tranny... what flywheel will i want to be using with the 351 and i cant reuse the one from the I6 right?? thanks
  6. 66mustangg

    T-5 Conversion -Preorder HELP

    Im am about to start to order everything to convert my 66 mustang (289) from a 3 speed auto to a T-5. I just need you guys just to check over to see if everything works together and what I am missing thanks. Im going with -G-Force T-5 Tranny -T-5 Conversion Kit Late Model Bellhousing...
  7. 66mustangg

    will this work?

    will a 351 clevland out of a 72 torino gt go into a 69 mustang with a 6cyl , 3speed, with no problems??? thanks
  8. 66mustangg

    351 windsor swap

    I am going to do a 351 windsor swap into a 69 mustang convert. right now it has a I6 with a 3 speed tranny...do you have any pointers or info that might help me get through it better??? thanks any info appreciated
  9. 66mustangg

    auto to manual conversion

    I have a 66 mustang with an auto trans and 289 in it right now. Im looking to convert it to a manaul transmission over the winter. right now i would go with a T5 but its only rated for 330 ft lbs of torque. either next year or the year after i want to put a new engine in it. probablly a...
  10. 66mustangg

    starting

    I go to start my 66 mustang today and i cranked it over once,and it kept on cranking over even if i pulled the key out. so i had to take the battery cable off. is it my starter selonoid, or anything else? thanks
  11. 66mustangg

    ignition switch

    i got my ignition switch out, but now I cant get it back in. can anyone help me with that?
  12. 66mustangg

    USA industries ALTERNATORRR

    does anyone have a wiring diagram for a USA industreies alternator, i need to see if i have mine wried correctly.. thank
  13. 66mustangg

    voltage regualtor problem

    Allright i just got all the wiring in my 66 mustang. i bought the complete body harness from painless performance and rewired the entire car. So i got it all in and troubleshot for the last week and finally got it to run tonight. but after i got it started it ran for about 2 minutes and then...
  14. 66mustangg

    IGNITION SWITCH

    How do i remove the ignition switch out of my 66 mustang? i searched the other threads and they said put a paperclip in the hole and turn the key to the left. I tried that and they key snapped.:bang: I got the snapped key out but i still dont know how to get my ignition switch out... any...
  15. 66mustangg

    Ballast Resistor

    Im in the middle of doing all my wirirng over and my kit came with a ballast resistor. I was wondering if i should intall it beacsue the directions give options on wheather to install it or not. and if i should, where should i mount it? thanks
  16. 66mustangg

    ammeter

    I was talking to this guy who owns a wire shop a couple of weeks ago and he was telling me that I really shouldnt hook up my Ammeter gague and I should just get rid of it. he said that all it does is cause problems. does anyone know if thats really true??? b/c i dont know if i should hook mine...
  17. 66mustangg

    Grounding Question

    hi, im doing all my wiring over right now...i got the painless full harness....but where did you guys ground the body to the chassis???.... i dont know where to put it
  18. 66mustangg

    Wiring troubles

    Heres the deal... I went to the wire shop to get my cars wiring fixed. The wire guy showed me almost all my wires were burnt and frayed. So he wanted 1500 to rebuild/replace most of the wiring, leaving some. So i asked him how much it would be to install a whole new chassis harness and he...
  19. 66mustangg

    Full Paint job

    Around how much would it cost for a full paint job for a 66 mustang coupe?? just to get an idea
  20. 66mustangg

    Undercoating

    What type of undercoating would you guys recomend....powder coating or a rubberized under coating or like anything else???
Top Bottom
Back
Forums
Menu