Search results

  1. ponyboy19

    Battery cut off switch, Alternator wire?

    Just wondering when you install a battery cut off switch on a 94/95, and you wire the alternator directly to the battery side of the switch, what do you do with the two wires that the original alternator wire attached to and that went into the power distribution box under the hood. Do you have...
  2. ponyboy19

    Did you use a bumpsteer kit with Sn95 spindles on a Fox.

    Just put on a set of 94/95 front spindles and brakes on my 92. Trying to decide if I need to buy a bump steer kit or offset rack bushings. I see the Tie rod's aren't quite parallel with the A arms but I'm wondering what others have done when doing the swap?
  3. ponyboy19

    E-brake cable. How to remove from rear end?

    Just wondering how the emergency brake cable is removed from the rear calipers on my 95. I haven't really looked at it but I'll be taking it off later tonight when I remove the rear end and thought I would save some time. Any help would be great..
  4. ponyboy19

    MGW shifter owners.. which handle?

    Just wondering if any MGW shifter owners would mind telling me which handle they have, how it feels, if they would get that one again, and why. Just not sure If I would rather have the blue or red?
  5. ponyboy19

    Another 5 lug conversion/rim tire question

    I'm planning on a 5 lug conversion on my 92 and want to be able to swap rim's and tires back and forth from my 92 to my 95. I have a set of 17x9 cobra R's and a set of 18x9 00 cobra R's. Will one or both of these sets of rims work with the cheap axle and rotor conversion like this one on my...
  6. ponyboy19

    Where is the TFI module located?

    I am thinking I'm going to replace this along with the PIP due to some issues that I think may not be tune related and was wondering where the TFI is located on the 94/95's. I admit I haven't looked for it but was hoping to save some time. And since my knowledge of the electrical compents are...
  7. ponyboy19

    4000 CFM dodge Viper fan install Pics & info

    Here are a few pictures of my electric fan set up.. I installed an AFCO 31x19x3 two core aluminum radiator along with the 99-2002 Dodge Viper Gen II electric fan part # 04854720AA. I was told that on low speed the fan will do 3000 cfms and pulls about 25 amps and drops to 8 amps once up to...
  8. ponyboy19

    Factory Fan Wiring Harness Question...

    I installed a Dodge Viper 3000/4000 cfm electric fan and I am going to use the factory harness to kick the external relay on to operate the fan. I have the fan wired on high all the time and I am going to use the factory low speed wire so it kicks on at the low speed temp. My question is which...
  9. ponyboy19

    Real Cars...

    Real Cars... anti rice Thought you guys over here might find this funny if you haven't already seen it. http://www.importforum.com/cgi-bin/yabb/YaBB.pl?board=Photo_Gallery;action=display;num=1087789077
  10. ponyboy19

    who's running a 31x19 radiator in their 94/95's

    Thinking of getting an Afco 31x19 radiator to fit in my 95. Just wondering who's used one and how much trouble you had getting it to fit. I don't see much about this on 94/95's. I'm not running anything but the radiator up front so no A/C condensor, lines, etc.. It' appears it will fit very...
  11. ponyboy19

    Question for anyone running a fuel cell.

    Tossing around idea's for a fuel system and I think I am leaning towards a 16 gallon fuel cell for my 95. Just wondering what cell people are using, how much hacking of the spare tire well was involved, and if you have a fuel level gauge installed either factory or aftermarket. I was looking...
  12. ponyboy19

    Anyone with 2.5 tailpipes and 275/40/17's

    92 gt. cobra rear bumper, anybody know or have used 2.5" lx tail pipes with 17x9 cobra R's and 275/40/17 tires. I am thinking they won't fit.
Top Bottom
Back
Forums
Menu