Search results

Well was cruising along yesterday, turned my ac on and instantly my car went to vibrating pretty bad, I basically idled it home, about 2 miles. Got to looking and the balancer pulley looked crooked so I pulled the belt and instantly saw what I thought was a broken crankshaft as the balancer had...

Hey guys, been a while. I bought a b&m hammer shifter for my 91, not sure how long I’ve had it, can look up later, anyways I have had nothing but problems with it, from park- I can go to reverse, to neutral, to 1st, to 2nd, to 3rd, that order. Reverse valve body c4, problem is, once I hit 1st...

Does anyone have a picture of the driver side of the shifter mechanics? I am having a problem with mine and the bracket that attaches to the cable that unlocks column looks bent or out of place, I got stuck in first gear and could shift no higher today, limped home and was able to push on the...

Alright, a few years ago i upgraded to 3:73 rear gears with an aod, I installed a mighty mite c4 last year, will the same speedo driven gear work in this transmission or will it be a different count, I had the white gear, unsure on the count off my head but it was pretty close with the aod, I...

Ok, car sat for a while, no problems of any sort other than fuel gauge reads past full at all times. I pulled the entire cluster, have not replaced yet, decided to do a quick drive in the car without the cluster in, battery drained to dead within about 5 miles, jump started the car about 3 times...

So to start I've been having an occasional miss, the other day the miss became permanent, what's new, msd 6al2, msd 8.5 wires, plugs, cap, rotor and tif module, the problem is that I was using a timing light to see what plug wasn't firing, all are, just that the entire drivers side is firing...

K, dart block 347, tfs head, srp piston, runs great, went to switch to synthetic 5w30 and have smoke on decel afterwords, only after warmed up though, plugs at rear of engine are oil wet, does not smoke in decel if pcv is out?

Simple story, rebuilt 347, first oil change to 5/30 royal purple, about 15 mile drive home, got on just a lil to reach speed limit and let off throttle at that point, huge puff of blue smoke? Got home and every time I gas it no smoke til I let off but just for a second, let it sit a couple days...

Finally got my shp block 347 rotating assembly finished, what oil pan fits best as there are no provisions in block for dipstick tube? Didn't realize until buttoning up bottom end? Also do I need a oil filter adapter? Just a threaded hole there?

Well, blew the stock aod transmission a few months ago and with kids and work just kinda put the stang away for a while, finally decided to get her going again and bought a built aod for it, I decided to pull the engine and tranny so I could go ahead and replace the rods, mains, and head...

Just a quick question, do you turn the Allen head out to lower the pressure on an aeromotive regulator, and what pressure would you recommend for a 347 with tfs heads, n51hr, eddy rpm2, 30lb injectors, 190 fuel pump?

Got my 347 up and running again but when I install the tiny little timing advance thing(forgot what its called) I can't get it to fire up without giving it throttle, it idles and revs fine without it but not with it in, any suggestions? It will also hunt for idle and die with it in.

Well I finally decided to pull my engine due to no oil pressure for the second time, first was due to a popped oil galley plug, this time the oil pump locked up and twisted my arp shaft off, first drive since i replaced the galley plug, so I was just wondering what is the best pump and shaft to...

First time it was simply one of the 3 galley plugs, installed a new one, test drove and was fine until I got on it again, this time I pulled the timing cover the 3 plugs were still in place, what now? Possibly the one under the intake, the rears are already threaded, or maybe the pump went? Will...

First actual drive after installing the new 347, I drive about 5 or 6 miles and its running perfect, get about a mile from home and my oil pressure just instantly drops, was hoping it was just the gauge, but it isn't,t getting oil to the rockers, I pulled my distributer to see if maybe the shaft...

Been a while since I posted here thought some of you could help me choose a good head for my 347 that has been sitting in my garage unfinished for over a year now, havn't had the time or the money to finish it up but I do now. So anyways I have an assembled 347, anderson n51hr camshaft...

Does anyone know of any tuners in Arkansas, may be willing to go to Oklahoma or Missouri if its close enough, I'm about an hour from LittleRock and will be needing a tuner in about 2 months. Never dealt with having a tune done so I don't know much about it, do they just reprogram the computer or...

Does anyone have a sound clip or video of this cam?

It's not the 5.0, it's the womans old 97 mazda millenia, we were driving it one day and it started struggling to go and finally died about a minute later and won't start back, the mechanic has had it for 2 weeks and finally said that he can find no reason for it to not start, I went and checked...

Finally got around to getting some new metal door handles (mine broke today) all they come with is 4 rivets to install them, just wondering if there is anything else I will need to install them.