Search results

Hello all, I'm swapping over to the Borgeson set up. I bought the Borgeson pump kit. They only sell the Windsor kits (No bracket for the cleveland). Well I found one and with minor modifications, fitted it to my cleveland. Here's the problem: The Borgeson pump return line sticks directly...

My wife broke out her equipment for a few shots. Check it out! :D <table style="width:auto;"><tr><td><a href="http://picasaweb.google.com/lh/photo/NdJFhSeB4MGQLXw7weTJ-w?feat=embedwebsite"><img src="http://lh4.ggpht.com/_ZxVQH2ua03M/SiHmg9jHgyI/AAAAAAAAAD8/5ASTpl8Eu3Y/s144/m4.JPG"...

I just got my 140A, 1 wire powermaster and stuck it on. I had to take a step back b/c I remembered my failed 3G attempt due to the infamous v-belt pulley goat rope...:nonono: Anyway, Powermaster didn't state you needed a fuse. They even provide the pre-crimped 8 gauge wire (which I promptly...

Link Okay, I have a bunch of stuff for sale, but don't quite know what to charge so please make offers. You'd have to pay for shipping. I'm not trying to get rich, but i'd like to get fair market value for this stuff. I just wanted to offer it to the Mustang guys before I placed it...

My setup is in the signature: My problem: -I don't know if i'm getting enought fuel. What I know: -I have a new Holley Fuel Pump(Model HLY 12-854) -I have a new 1411 Eddy Carb, tuned to the best of my abilites with a Vacuum gauge -I have approx 9" of vacuum @ 800 RPM. I've checked for...

Okay, I'm in the tune phase of my rebuild. I went with the vintage air a/c. With the A/C off I idle around 800. However, with the A/C on, I loose idle tremeduously....to the point of stalling the motor. No problems with driving around. It just dies occasionally at the light. Any ideas? If...

I bought a universal radiator at the advice of the Summit Cust Serv. As you can see from the pics, the radiator fits pretty darn good! The problems are 1) My Ford Taurus fan is a little too thick and 2) the lower (driver side) hose sticks up at a 45* angle....:eek: It points at the pwr...

Sucks! Working on installing a T45 and am trying to test the Runout. Any advice? As I go through this process, I realized I had the wrong separator plate. Once I got the plate, I put the bell housing on to test the Runout only to realize I had to draw the bell housing onto the studs with...

I'm in the middle of swapping my automatic tranny for a Keisler T45R. I got my hands on a 1970 clutch & brake pedal so I refurbished it and installed it. This setup has the clutch and brake pedal on the same rod. My original one had the long brake pedal that mounts where the J-mount for the...

I'm performing a tranny swap. (Keisler's T45R kit) I chose the hyd throw out bearing. I'm wondering if I should remove the J-stop spring. The reason I ask is because my clutch pedal goes to the floor and stays there. Granted everything is not hooked up yet, but i'm wondering if the hyd...

Sorry to roll in here looking for instant help, but I need to make a decision tonight about this rack and pinion. Yes, it is from FR. It pretty much has everything from the rack to the steering column and pump. Most of all, I can get it by tomorrow. Which is important b/c i'll be finishing up...

Anybody know of one in the local area?:shrug:

I'm planning on rebuilding the cleveland in 2-3 months. Lookin' to get 300 rwhp out of the thing and still get somewhat decent gas mileage. I'm wondering should I go to 4V heads. I'm also wondering if I should stroke it. I'm thinkin' strokin' is a bad idea due to gas mileage. I'm pretty...

I may have to change my timing cover. I think I may have water passing through. Questions? 1. Where in the heck can I buy a 351C Timing Cover? 2. Since I may have to tear the front of the enging apart, I was wondering should I replace the damper. How could I tell if it needs replacing...

I have a C-6 on my 70 Grande'. It must be a tranny swap by the guy who had it before me. Anyway, I've had it for about 6 months and the tranny has never leaked. Well, that is until I noticed it being about quart low on the dipstick. I filled it and checked it properly(in park, after a drive...

Anybody going to Mustangs Plus 2006 Car Display in Stockton, CA? It's on Saturday Oct, 21st. Best part about it is it's free! :D

Just installed a new stock fuel pump on my cleveland. It came as a 2V-2bbl, but It has the Eddy performer manifold and 1407 4bbl. I'm having problems getting this thing to idle. It was running perfectly before the fuel pump swap so I would assume that it would run just the same if not better...

Excuse the mess.....I know it looks like my old suspension blew up in my garage.... I knew these were going to look good, but not this good. I slap the rubber on Friday afternoon. I'll upload another pic when I get the finished product back.

I'm thinking about ordering these this week and wanted to know if anybody has experience with these or has had issues with the fit. Better yet, pics? http://www.mustangsunlimited.com/itemdy01.asp?T1=7865K+01&Category=Wheels+%26+Brakes&subCategory=Wheels&CatKey=EMUSTANG Ultra 454s: 17x8s...

I got a free ticket to Motorworks 2006! http://www.mccallmotorsports.com/motorworks.html A bunch of millionaires showing off thier upper 7 and mostly 6 figure toys.... Absolutely ridiculous! Not many American Cars around, but there were a few stangs. Including one with wings! Anyway...