Search results

  1. MadPony

    Fox vs SN95 decel observations

    Welll the only thing II have to add, is the base idle (IAC) disconnetoed, should be where the car will actually run. Its not a hard and set 600-650. Set it to the min rpm that it will idle at. Then you actual idle rpm that you set in the eec will be 120 rpm higher than that. The bigger the cam...
  2. MadPony

    Backfire BANG and stall. WONT START

    Check your Distributor to make sure its spinning, if it is check the timing. This happened to me. I had stripped the gear on the camshaft.
  3. MadPony

    Why do we need the PCV system?

    Well, 2 reasons, even well built stock motors get blowby to a small percentage, as there is an end gag in the rings. During the compression cycle some of the gasses that get blown by the rings is fuel and air. These gasses build up in the crankcase, and could potentionally explode :-(. The...
  4. MadPony

    Oil is DRIPPING out of my upper intake manifold.....WHY?!??@!

    man if you are blowing intake gaskets off the base of the intake, there is some serious blowby that needs to get evacuated.
  5. MadPony

    Bad Vibrations... HELP!!!! Video Inside

    I am pretty sure torque on the crankshaft bolt is 210Ft/Lbs. The trick is not just the torque but to make sure it is seated all the way up against the timing gear. It is a press fit, so it takes some force to get it on. Typically I tighten it down make sure its seated, then loosen the bolt and...
  6. MadPony

    Camshaft thrust BEARING?

    From the advice I was given, when you are using BIG cams and the engine is loping, especially with the cam driven dizzy and oil pump the camshaft tends to walk more than normal, if you can keep your idle out of the lope, then its not so bad. I originally had an X303 cam, which is why I put in...
  7. MadPony

    Oil is DRIPPING out of my upper intake manifold.....WHY?!??@!

    well, it sounds to me like you have a considerable amount of blowby. I have my motors ring gapped for NOS, and I have considerable more blowby than a stock motor. Its driving me nuts too, thinking of tearing it down in a few weekand and putting new rings in. In between time I have a steeda oil...
  8. MadPony

    Camshaft thrust BEARING?

    I have one in mine, but I bought it from a local dealer for about 1/2 the price. However that was a year ago. Going to do a tear down this winter, will let you know how it held up.
  9. MadPony

    How hard to rebuild motor, and how much????

    The only issue you will have is putting new cam bearings in, other than that it is easy. Do not try it without a proper cam bearing installation tool. They are only abbout 100 bucks, but its worth the money if you get one in crooked. Still for the amount of effort, by the time you get the...
  10. MadPony

    How hard to rebuild motor, and how much????

    personally I would go to ebay and buy a shortblock, a lot of performance houses have good deals now. I would make sure you get references, before you buy though. Then take you heads to a local machine shop, and have them ported and polished. If you take the motor out yourself and install it...
  11. MadPony

    Vibration at 80mph+ since gear install.

    one quick thing to try us unbolt the rear u-joint (connected to the ponion side). flip it 180 and bolt it back up. Don't know why but I have sen this before. Anytime I replace ujoints, I always mark each piece, so it goes back in the same way. I have seen too many driveshafts vibrate after...
  12. MadPony

    Blew a Head Gasket

    I mentioned that you needed a wideband back on oct 10th on the other site. You also need to keep your foot out of it, and back out some timing till you get the AFR dialed in.
  13. MadPony

    anyone making mail-order tunes?

    Based on my year working on the MadPony, there are a few necessary tools you need: 1) TweecerRT 2) Eec Analyzer ( chart, view, and analyze logs. It will give you some good base numbers for injectors and MAF slopes). 3) Wideband necessary for WOT tuning. Also make sure everything is the...
  14. MadPony

    anyone making mail-order tunes?

    Based on my year working on the MadPony, there are a few necessary tools you need: 1) TweecerRT 2) Eec Analyzer ( chart, view, and analyze logs. It will give you some good base numbers for injectors and MAF slopes). 3) Wideband necessary for WOT tuning. Also make sure everything is the...
  15. MadPony

    Lets start from the begining! What to do next? $10 to the person who helps the most!!

    Ok email sent with my contact info.
  16. MadPony

    J4J1 Injector Timing via EEC Analyzer

    What exactly are the cam specs, and what other mods have you done to the car.
  17. MadPony

    Lets start from the begining! What to do next? $10 to the person who helps the most!!

    I dont use the J4J1 anymore I was having too many driveability issues with it. Sounds like you have had a few issues. I am running a 95 GT full mods can be found here http://www.badazzponys.com/html/mad_pony.html. I willd owhat I can to help out. FIRST and most important, get the WB hooked up...
  18. MadPony

    Tip Accel Problem

    Aaargh Well its back to the drawing board. My distributor siezed up and tore of the cam gears. So I wil lbe getting a new cam. So I may as well start over again. Does nyone have a good J4J1 bin I can use, or know where I can find one?
  19. MadPony

    Car Pulls to Left on the Brakes

    Similar issue I had a similar issue, replaced brakes, calipers rotors.... turned out to be a bad balljoint. now no more porblems.
  20. MadPony

    Throttlebody/Pro-M 80mm

    EA Do you have Eec Analyser, if not it is worth the 50 bucks. there are a lot of notes in the help files to get your Tb airflow set up. Once you get it let me know and I will send you the bas 30pt curve from my prom80.
Top Bottom
Back
Forums
Menu