Search results

  1. gtsr281

    TRanny problems

    Your pan is no problem, could just check to see if it's tight and replace the gasket. The other situation could be that the pump is loose......or the torque converter welds are letting go, I have seen this happen. I put the transgo HDII shift kit, B&M 24K GVW cooler on, and redline clutches...
  2. gtsr281

    I am SICK of people asking me how much my supercharger costed

    I never have people ask me how much it cost, I always get how much power i'm putting down.
  3. gtsr281

    600HP on stock crank?

    that much TQ I would build the motor from top to bottom, I have recent EXP with blowing **** up because no matter what hear say you may have, anything stock is not to good considering you have boosted the HP/TQ by almost 300. Dont forget about the Trans, and rear end, all that needs to be...
  4. gtsr281

    Pulsing/ Jerking In drivetrain under Accel..

    I had that problem and later installed the transgo HD shift kit. It has now gone away, it's more likely to be tranny problem. The AODE 4R70W is a ****ty trans. I blew mine out three times so now i got the T-56 6 speed HD.
  5. gtsr281

    T-56 6 Speed

    I have the 4R70W auto in my 01 GT, i blew it out because of the RWTQ, now i', having nothing but problems each and every week, I have gone and purchased the T-56 HD 6 Speed but i have never converted over to a manual from auto in a ford. I have on the other hand done it on camaro's and from...
  6. gtsr281

    Exhaust work

    I have decided to go with an aftermarket type V.S. OEM stock
  7. gtsr281

    Exhaust work

    Neh i have decided to go with an aftermarket V.S. OEM
  8. gtsr281

    Exhaust work

    I did some research on the cobra crap and decided to go with an aftermarket upgrade it is only about $250 difference from OEM
  9. gtsr281

    Exhaust work

    I have a 01 GT Mustang Auto, and i want to put on the Cobra exhaust. The dimensions for stock is 14.00H/21.00W/59.00D..........and the Cobra kit is 14.00H/21.00W/54.00D.....now is this gonna cause a problem with the install, or will it be a bit short on the exit of the car?
  10. gtsr281

    Found out I'm diabetic

    i am a type 1 and that is insulin dependant, i have had it for almost 20 years now. Be very carfull and keep it under control, i passed out behind the wheel on the highway because of a insulin reaction and hit someone head on at 65mph. Watch your diet and test often dude this **** is very...
  11. gtsr281

    AODE 4R70W

    i got the AODE 4R70W auto transmission in my 2001 mustang GT i put new clutch paks in it, and seals, along with the transgo shift kit, my problem was i snaped the intermidiate stub shaft which i have replaced along with the drum, now it will not engage drive gears unless in 1st on the the...
  12. gtsr281

    car will not start after trans work

    this plate you talk about it's located on the bottom of the trans and has three bolts holding on right if it's that one then i have it on
  13. gtsr281

    car will not start after trans work

    i tried all gears p r n d 2 1 still will not start and i cant seem to find a relay or fusable link :bang:
  14. gtsr281

    car will not start after trans work

    i built up my transmission it's the 4r70w when i put it back together the engine wouldnt even turn over, i checked the starter all wiring is correct, the battery has a good charge but when i tested it, i get good connection from one wire but not the other and no fuses are shot???? i'm thinking...
  15. gtsr281

    car will not start after trans work

    i built up my transmission it's the 4r70w when i put it back together the engine wouldnt even turn over, i checked the starter all wiring is correct, the battery has a good charge but when i tested it, i get good connection from one wire but not the other and no fuses are shot???? i'm thinking...
  16. gtsr281

    transmission parts

    does anyone know where i can get trans parts for the 4r70w auto it came out of a 01 GT the parts needed are intermediate shaft stub, and possibly the cylinder assembly-direct clutch, any info will help thanks
Top Bottom
Back
Forums
Menu