Search results

ABS also offers a box, not a modified box

We installed new SS fuel lines, original style. The tank we had had the outlet in the same area as stock, so we simply used AN fittings and attached the braided hose to the fuel line, we did shorten the hard line somewhat.

We intstalled a Fuel Safe fuel cell purchased from Reenmachine in our 65. Fit was same as stock, we opted for the standard 16 gallon variety. It fits like the original. The outlet is similar to original. We do have a vent out the top of the fuel cell exiting below the taillight panel thru the...

They are all pretty bad. We had a '65 FG hood from Maier and after sitting, it warped so bad we trashed it and had a steel hood fabricated with the scoop. By time we were done, it would have been cheaper tohave gone with the steel to begin with. We also had the rear decklid with the spoiler...

you can get whatever intermediate shaft you want as far as length goes. the main item needed is a support for the shaft at the bottom of the steering tube. Assuming from you earlier comments, that you are using your original shaft. You need to supporot yhe shafr in lthe column tube with some...

You may want to check with Randal's Rack. His kit comes wiyh a machined piece which goes into the lower end of the tube to support and center the stock steering shaft when cut off to use his R&P. seems to me I have seen an article regarding this modification in one of the magazines or possibly...

Based on your anticipated useage of the vehicle and your statement of "minimum: Probably could do without align boring the main caps. Hot tank the block, clean out all passages, new cam bearings are required More than likely, your cylinder wall taper will require going oversize on the...

the shop that did our '65 does not like chemical stripping. the prefer "media blasting". A word of caution regarding media blasting. You have to find a shop that is use to doing car bodies. If you get the wrong shop, they will warp the metal then you have really serious problems. When you...

If the factory primer has failed, then you have to go to the metal to eliminate the problem. Most good body shops won't want to paint over anyone else's body work. If it fails, then the paint fails and guess who you'll be mad at? Going Black adds cost as it has to be REALLY straight or it will...

try talking to TCP? They've always been responsive to any questions I've had

they all sell the same (molded) brand, Auto Custom Carpet. So pretty whoever you buy from, you are getting the same set. For our current project, we went directly to Auto Custom Carpet and ordered their Mass Backed carpet, much heavier quality and great fit. It is stiffer and a little more...

suggest you look into Cerullo seats. We are using them in our 65. they will also reupholstery your rear seat for you to match the fronts. they will make them in all vinyl, cloth, combination cloth and vinyl or leather. they are also made in Southern California and not imported.

not street legal =

I concur with rbohm. we're using the flex form composite leaf springs. Significant weight reduction along with the ability to pick whatever springrate you want. we are using 225# springs with Bilstein shocks on our '65. purposely a little stiffer. They are custom made for you

it is a 8" with a Currie center section. 3:55 with a tru trac. the disc beake conversion kit is from ABS

we also have the flex form springs, although we havn't had much time on the street, we are happy with them. they use the stock shackles . ours are 225 # springs.

I went over and was able to measure the depth. they are a little over 2". we found that the infin ity speakers (6020 model # as i recall) works very well. one place i've found that has good pricing on electronics, including dynamat is an online company at techronics.com. they are cheaper...

our Sub enclosure is behind the panel holding the amps and other components, so it is hidden

these allow close to 2+". we are usiny Infinities 6020 speakers which has a depth of 2 1/16". they are deeper than the more common units.

only the ones we showed in our prior post. i won't get any more done for a few weeks. i'm working one-handed at the moment. is their something in particular you were interested in?