Search results

I'm trying to figure out the pushrod length for my 351w 408ci stroker build and I'm running into a snag. My block has been decked to 9.482" and I am using AFR 205cc heads with Comp Cams Pro Magnum rockers and Comp Cams Endure-X roller lifters. The cam is a custom grind from Flowtech Induction...

Has anyone here used a Turn One power steering pump before? I'm looking for a power steering pump that can handle extended high rpms and not have the steering feel "loose". I'm looking for a good road feel during racing. Anyone have a pump they recommend if not Turn One?

Is anyone using one of these with a serpentine pulley setup? Under the application on summitracing it says, "Not for use with serpentine drive systems." Anyone know why?

I have heard of people putting 1966 Dashpads on their 1965 Mustangs. What are the differences between the two, and why would someone decide to swap the dashpad out for the later year?

I bought a late model 351w block that has been bored .030 over, and I have a set of JE SRP forged pistons for my 408ci stroker kit that are also .030 over. Should I try to get a set of pistons that are .040 over so that it is possible to hone the cylinder to the piston or should I just put the...

While researching ways to implement a security system for my car to prevent theft I came across this idea of an inline check valve to lock the cars brakes while you are away. This would prevent someone from just hooking a tow truck up to your car and towing it away. Has anyone else heard of...

I've looked at Canton, Moroso, and Milodon oil pans and I'm not quite sure which one to go with. I'm looking for a good road race style oil pan. What company makes the best oil pan?

Does anyone know of a decently priced six gauge instrument cluster for a 65/66 Mustang? Last I checked there was only the extremely expensive setup from JME Enterprises. http://www.mustangdepot.com/OnLineCatalog/Interior/jme65-66clust.htm I have found a six gauge bezel from...

I'm looking at this pump here: http://www.holley.com/12-289-25.asp Do you guys think it will be enough for a ~600hp engine? 351w 408ci stroker AFR 205cc Heads Edelbrock Victor Jr. Intake Manifold Bigsperformance custom Holley 950HP Carb Flowtech Induction custom mechanical roller cam...

Does anyone know the holding capacity on one of these, all I can find is 90% Greater Holding Capacity, but what does that really mean? I'm looking for a number horsepower wise.

Does anyone here run 1 3/4" headers with a cable clutch? I'm running a mustangsteve cable clutch kit in my '65 coupe with a 408w hooked up to a TKO 600 with a lakewood scattershield. I have a mustang II front suspension so clearance to the sides won't be a problem with no shock towers, but I...

My driver side door is full of bondo, and my passenger side door is caved in around the door handle. Should I buy door skins and replace the sections of the doors that are bad, completely reskin the doors, buy brand new repo doors, or try to find original doors (no luck so far)? The door lines...

I'm currently Camshaft shopping for my 408ci 351w build and I am considering a custom camshaft from Flowtech Induction. Has anyone dealt with them before? I've been dealing with Ed specifically. What is everyone's opinion on a custom camshaft vs. a factory cam such as Comp Cams. I'm planning...

I just acquired some seats from a wrecked 2002 Mustang GT. The mustang only had 14,400 on the odometer so the seats are pretty much mint condition. I bought both of the front seats (drivers side power), the seat belts, and the parking brake handle for $340. :D They are "black" which nowadays...

I originally had plans to undercoat my car with POR-15 but now I'm wondering if powdercoating might be better. My goal is to make it all bulletproof. Do any of you guys have experience with powdercoating vs. POR-15?

I don't know much about tig welders but I found this on e-bay: Tig Welder/Plasma Cutter it's a combination tig welder and plasma cutter which is nice because I'm wanting both. Does anyone know anything about this seller or about the welder?

I'm selling 2 brand new never used 17 x 8 5.72 BS '03 Mach 1 wheels because I'm going with a different wheel offset. They look like this: PM me for details. Thanks, Jeremy

I am installing the Heidts Mustang II kit into my 65 coupe and I'm running into a little problem when measuring the notch for the frame rail. Maybe some of you guys that have done this kit before can help me out. The boxing plate is hitting the sway bar mount and will not center on the 24 1/4...

I am building a 351w engine stroked to 408 for my 65 coupe and I'm looking for some input. With the stroking, I'm thinking the revs will be limited to about 6200 to 6500 rpm max if I am correct. I'm looking at AFR heads, specifically the 185cc or 205cc models. I think that the powerband might...