Search results

  1. G

    Nothing to see here, move along...

    wel what ever ill go to my other 10 sites im on.:rlaugh:
  2. G

    Nothing to see here, move along...

    thanks but that never seems to work for me , its like you got to pay for it ?
  3. G

    Nothing to see here, move along...

    No sales in the regular discussion forums. Matt
  4. G

    03 cobra s/c belt tensioer ?

    thanks for the reply i got only 100 mm ider as you can see in this old pic .i had only 1 100mm out at the snub idler, that pulley is a 3.25 , i got 2 100mm up top now. so the way i checked it isnt the correct way then? , right now its got about 1/4 from being all the way to the stop . plus the...
  5. G

    03 cobra s/c belt tensioer ?

    03 cobra s/c belt tension ? -------------------------------------------------------------------------------- i just put the other metco 100 mm idler on it i had a shorter belt thats new. the ten. is so tight it only got 1/8 of movement after the belts on. i want to make sure it dont slip...
  6. G

    Knuckle, mustang, left - w/independent susp - W/INDEPENDENT SUSP

    i got both sides for a 03 cobra no tears 28k b4 going sra. pm me
  7. G

    What octane do you run in your cobra?

    03 cobra here 2 tunes 93 pump 104 sunoco unleaded
  8. G

    Where to find a 96-98 Cobra rear bumper cover?

    pm sent
  9. G

    2003 cobra only driven around the block

    still waiting for pic of car?
  10. G

    20 psi with 2.6 k/bell look .possible?

    i got 603/525 on 93 pump at 19.6 psi and 17 deg timing 641/557 on 104 unleaded gas at same boost level. with 20.5 timing 643/576 on 104.. at 21.5 psi> really didnt improve the hp. pulled 3 deg due to high ait2 temps. tuned by amazon mustang dyno #s i had jms tune it 1st they suck! they...
  11. G

    E-brake light is on

    i got the same problem my light comes on on a jerky stop , like quick stops the fluid is up to the max mark? all i did was put a k/b 2.6 on it ? and this started? bad float i think?
  12. G

    03 cobra k/bell noise?

    i was told the noise is normal?
  13. G

    03 cobra k/bell noise?

    its a wirling noise right at the center of the unit? i never heard a kenne bell unit run be this might be normal? but not sure hoping someone with one can help me also when i give it just a little gas , it goes away, when back at idle, you can hear it .
  14. G

    Im tired of Ls1 smack talking

    there just jealous thats all. a 4.6 to a 5.3 is a big differance in cubes. i think there 5.3's ? tell them to s/c theres and stfu ,
  15. G

    03 cobra k/bell noise?

    ok i got my 2.6 installed ,'new unit'' does it have to be broken in maybe?'' it seems to have a noise coming from the middle of the unit, i spun all the pulleys and they seem to be fine, it never made this noise with the eaton? im wondering if this noise i'am hearing is normal? its like i...
  16. G

    IRS Trac-Loc rebuild

    jack car up. see if you can rotate tire the oppsite way or hold one if you can spin they other side with ease them its weak. my 03 cobra had 28,ooo miles and it was gettong weak alreay. my 99 cobra had 58k and was still pulling posi to the right . working on the irs sucks , i got solid axle now.
  17. G

    04 Cobra has developed a strange whine.

    could be pulley , my kn fiter makes squssing noise from sucking in air kn fipk one could be you bearings take belt off and spin them?
  18. G

    octane question!

    ok , i got a k/b 2.6 with 22 psi , sunoco 104 octane gas will be enough right? cause you can run 18 psi on 93 ? a person at k/b says it wont be enough? i wanted to see what youa ll thought thanks! i think i could run more then that like 24 psi?
  19. G

    Cobra IRS wheel hop

    mines not a race car . and a swapped , it looks better under the rear now . you can fool people to thinking you got a cobra clone , by looking at your exhast , them tell yes it is ,, then smoke them.
  20. G

    Cobra IRS wheel hop

    i got a buddy wi th 95 rear end minus brakes with 4.10 for sale for 300 bucks pm me , o and no axles . i got some out of 97 if theyll work ?
Top Bottom
Back
Forums
Menu