Search results

What kind of lube is being used in this instructional video? Thanks! https://lmr.com/item/LRS-6758B/mustang-oil-fill-to-throttle-body-pcv-tube-86-93-5-0

What is a complete black tweed rear seat in very good condition worth. I saw one on Ebay for $1,000.00 !

Thinking of one of these projects for next Winter. It's a tough choice. Sometimes I just can't justify spending that kind of money to go 1 second quicker in the 1/4 mile LOL! I run 12.3's generally with my current set up Ford Racing Crate Engine...

So I saw this thread from 2020. https://stangnet.com/mustang-forums/threads/fuel-pressure-regulator-help.914154/ I have a Holley adjustable fuel pressure regulator. I've always checked / adjusted my fuel pressure with the vacuum off the regulator. I saw in this thread to take the vacuum line...

I am going to take the heater box and core out of my drag car. I'm looking for instructions or a link on how to do this please. Thanks for the help!

I currently have the green diagram in the link. https://lmr.com/products/fox-body-belt-routing-length-50 I eventually want a manual rack. So the power steering will be gone. I saw the short belt configuration here on Stangnet...

I am currently running Hoosier 26x9x15 slicks. (10.5" section width) Thinking of going to 26x10x15. (11" section width) Will they fit? 42423 HOORAC-Spec Catalog (2).indd (hoosiertire.com) Thanks

Comp Cams offers a GT40 valve spring upgrade kit. They don't have installation instructions. I was told that the installation is straight forward. I have now knowledge or the specs on how to do it. Thanks!

I have the factory air intake tube with the stock air box. I'm thinking of swapping it with a tube that doesn't have the ribbed bends. I don't know if it will make a difference? I use to have a C&L tube, but the person who temporarily owned my car put the stock tube on. I can buy a C&L tube...

Well my mechanic did a compression test on my old Ford Racing Crate Motor and it wasn't good. It served me well 15 years drag racing. Here's the link from the one I have. Ford Performance Parts M-6007-XB3M (summitracing.com) Does anyone know of any companies that make something very similar that...

I'm swapping my T-5 to a C-4. Will my starter work with the C-4? Thanks

How do you test the MAF Sensor Harness on a 1993 GT Mustang? Thanks

I use my car strictly for drag racing. I was told by a fellow racer at the track, that if I put a F303 cam in, a Trick Flow Track Heat Intake, 30 lb injectors, 75mm throttle body, I would run 12.4 et all day. My car runs 13.1 to 13.3 Sounds like big gains from just a cam, intake, and...

Street or Strip 1993 Gt Mustang (Florida car, no rust), new battery last year, 345hp Ford Racing Crate Motor, Edelbrock upper and lower intake, electric fan, MSD Coil Blaster, MSD Distributor, Holley Adjustable Fuel Pressure Regulator, Holley 190 LPH Fuel Pump, Tremec T5-Z transmission, B&M...

Ok, I am thinking that one side of the rears gets more wear than the other, possibly the passenger side. I have 93 Mustang, 13.2 ET average, stick car, with a Detroit Locker. Swap the slicks side to side about every 10 passes. Does anyone know what side would get the most wear from launching...

Coolant is leaking out of a plug, in the engine bay, on the passenger side firewall. I assume it is from the heater core. The plug has an open end, not sure if it is missing something. Any help would be great! Thanks!

I was fixing the wiper motor on my daughters 87 5.0. I was just wondering what purpose the hood grille serves besides letting water run into it. Thanks!

Bought a used MAF sensor still in the MAF meter housing. The screws that secure it are torx type. Only problem is, there is a pin in the middle that would obstruct the torx bit from seating. Where do I get a bit like that and what size is it? Thanks

My check engine light is on after re-installing my upper intake. Showing code 31. How do I test the EGR to see if it is shot? I didn't have this code before taking off my upper intake. I'm 99% sure everything is hooked up as before. Any help would be greatly appreciated! Thanks!

I took my upper intake off so I can retorque my lower intake bolts. There was some coolant puddled toward the back on the passenger side. The hose that goes from the lower intake to the back of the throttle body looked swelled, so I wanted to replace it while I was at it. Pulled the hose off and...