Search results

  1. J

    what head gasket do i need

    hey all, i'm getting ready to reasamble the block i bought, i changed the cam(f303) the heads are gt40 cast iron, i'm going to do some minor porting to them, my friend said that i should get thinner gaskets to bring my compresion up, what are my options ? i don't know if it matters but is going...
  2. J

    GT40/GT40P Head questions

    gt40 u can still use them...
  3. J

    how do I tap into negative coil wire for tach signal?

    when i installed my tach i was just testing it, i pulled the plug from the coil, stucked the tach wire and plug it back on, I did it as temporary, but i don't remember changing it, i'll have to change coil in 2 weeks for my carb setup, so i'll do it right.... test it see if it works...
  4. J

    fuel injection or carb

    ^^ You the man!!
  5. J

    plastic gauge questions

    don;t do i need that plastic gauge stuff to know if i need thicker bearings thanks javier
  6. J

    plastic gauge questions

    anybody?
  7. J

    plastic gauge questions

    hey all, i just got my block last week, everything looks good, but to make sure i want to check the rods with the plastic gauge stuff. where do i get it, and what numbers will i be looking at for a healthy crank... thanks javier
  8. J

    Are gear ratios stamped on Ford ring and pinions?

    yeah bigcat, but i figured if someone had a 3.55 set matty22 would know the amount of teeth that the ring/pinion needed to be...
  9. J

    Are gear ratios stamped on Ford ring and pinions?

    by math, they are 3.08 :( my ring was 41 and my pinion 10 if u devide the ring by the pinion u get the ratio.... if anyone has a 3.55 could you count the teeth to verify, thanks
  10. J

    gt-40 / gt-40p specs needed

    super, thanks again man
  11. J

    Are gear ratios stamped on Ford ring and pinions?

    count the teeth on the ring and on the pinion and let me know i believe my pinion said 4.10 on it... i don't remember about the gear. post the count #'s
  12. J

    gt-40 / gt-40p specs needed

    well the F cam is free, so i figured i start with that, 300hp/300+tq to the wheels is plenty for now, i hope the heads are not P, i don't want to look for an exhaust, i want the car on the road !!!, i can't wait anymore. btw, how big was the carb? 750? doi need rocker arms too? or push rods...
  13. J

    gt-40 / gt-40p specs needed

    cool, thanks by the #'s the P is better than the gt-40??
  14. J

    NYC / Metro Emissions

    there is a place in queens, i know is near shea stadium, you have to go up to the guy and tell him you need to pass inspection no that you want to do the inspection. and if u are willing to come to long island, there is a place near me also, but is like 150 or so.... either way let me know, i...
  15. J

    gt-40 / gt-40p specs needed

    hey guys, i'm getting an engine from a 94/95 gt low miles with gt-40 or 40p head, i'll know on saturday. i'm only paying 500 for it, i have this program that u can input the head specs and stuff and gives you an estimated HP/TQ graph, I was wondering if anybody had any specs on flow and...
  16. J

    fuel pressure regulator question

    in spring i'm swaping my efi 86 gt to carb. i have a 600 cfm edelbrock carb a performer intake i need a regulator, since i'm using my stock pump, i understand i need something with a return line or a 3 port reg. will this mallory work? MAA 4207...
  17. J

    need 2nd opinion

    thanks guys, i picked it up yesterday, looks really good, as soon as the temp comes up a bit, i'll go outside and take all the stuff off with some carb cleaner, and leave it ready to intall. thanks again javier302
  18. J

    need 2nd opinion

    thanks man, i'm kinda scare because it says "THIS INTAKE HAS BEEN GASKET MATCH AND BOLT HOLD HAVE BEEN WIDENED FOR USED WITH ALUMINUM HEADS" i have an edelbrock 600 cfm carb, that will work as well with it right?
  19. J

    need 2nd opinion

    nobody?
  20. J

    does anybody know

    i capped everything, car runs fine... surges sometimes at idel, but it was doing it before i removed everything... i also have an 86 with no c.e.l. i'm installing a carb in srping, so i wasn't really worry about anything...
Top Bottom
Back
Forums
Menu