Search results

  1. dartvader

    Need help

    Hi guys I have a problem with my car, its getting water in cylinder 6 & 7 went to start the car the other day and it won't start, cylinder was full of water :eek: so took the plug out crancked it and the water came out, I put the plug back in and it starts no problem then the other day I...
  2. dartvader

    Timing again ...

    Most peeps set their timing base 10* . If you had more mods maybe you can go 12>15 base, but a famous tuner wich I have a lot of respect for told me, they rarely go more than 14*base on the dyno, cause with 92 0ctane they don't see more power with more timing.
  3. dartvader

    New AFR 185 competitions tested at the track... New best 1/4 stats inside!

    That is sweet Paul :nice: told you you didn't need a turbo :D
  4. dartvader

    MSD distributor...can i replace PIP?

    Don't know if that is your problem, but if your thinking about replacing the pip go ahead and try to find a stock distributor from a friend to try out first.. Don't know what it is abouth these msd dis, but once you mess with them they never the same, trust me when I say that, I would not put...
  5. dartvader

    Here's what I did with my weekend... (typical last minute decision for me)

    That toy is cumming together nicely :nice: I think you'll get pleasantly suprised at the track Good luck Paul.
  6. dartvader

    AODE trans tuning

    Don Lasota at LaSotaRacing he will fix you up nicely :nice:
  7. dartvader

    New Best in the 331....

    So what is the power adder your using ? :shrug:
  8. dartvader

    custom grind cam questions????

    Ed curtis here, got what I asked for and more :D
  9. dartvader

    308 with AFR 185's

    I would call Ed and order a custom cam and those heads flow like 270 cfm, you need an intake that flows as much or close to those heads, holley systemax 2 or a fully ported upper lower edelbrock performer rpm by T- Moss would be sweet. oh and 4:10 gears and a tune, now you got a whole...
  10. dartvader

    308 with AFR 185's

    that thing should rock with the 185's, what intake do you have ??
  11. dartvader

    Why won't my car idle? New 306 build w/ edelbrock performer HCI

    I told you before, telling you again first ting you need to do is tune the car, my car would not even run after the HIC swap until i got a chip from Don La Sota.
  12. dartvader

    Quietest muffler you can have

    Borla XS with longtubes here, notice you can hear the engine more than the exhaust.... "]http://[/URL]
  13. dartvader

    Torque converter recommendations

    +2 for the Edge 9.5, I have only good things to say about it :nice:
  14. dartvader

    Trouble Finding Powerband

    earlys94gt, the intake your planning to use would work fine with those heads, while the 19 cam would make power to 6000 rpm, there's no way your going to get there with the stock pcm. so a chip would fix that, and the same time fix any issue's you may have with 4:10 gears :shrug: I really...
  15. dartvader

    Trouble Finding Powerband

    I don't understand your question too well, but if you have an AODE then 4:10 is the way to go, unless you spend a lot of time on the highway. AODE's need all the help you can give em, and don't forget the shift kit, and if you have the funds a converter too :nice: good luck
  16. dartvader

    331, 347, or 408?

    i'll go 331, with the price of gas going up every day I would not want to drive a 408 around every day. 331 afr 185 heads, holley intake and aaaaall the supporting hardware should be a fun streetable car and still keep your car in one piece . most people don't realize that when you have a car...
  17. dartvader

    " is it worth the trouble "

    well Grady, the last time Ed was here we talked about it :Track: he told me I would need another intake and it would work with this cam, he could make another cam for me if I wanted to make 100% benefit from the new setup = (more rpms and more gears ) I wanted to see if I could get some...
  18. dartvader

    Anybody running a cam with their Aode without a stall?

    Sorry it sounds so confusing :scratch: iphiniti im running an AODE also it will probably last forever for this horsepower level and the way its build. what i meant is the 4R70W would allow you to accelerate a little faster because of the higher gears in it .would it make a big difference...
  19. dartvader

    Anybody running a cam with their Aode without a stall?

    why is that ? its just a stronger automatic with wide ratio first and second AODE ------------------ 4R70W first 2.40:1 gear--- 2.84:1 gear sec 1.47:1 gear---...
  20. dartvader

    Anybody running a cam with their Aode without a stall?

    Iphiniti, I don't have dyno numbers but I went 13.09 with a 1.80 sixty feet. maybe some more timing was running base 10* total 33*and a underdrive crank pulley i would see high 12 my tranny has been rebuild with Performance Automatics internals and shift kit, if I would do it all over again I...
Top Bottom
Back
Forums
Menu