Search results

  1. 98stangalang4v

    i got a tough but simple speedcal ?

    last weekend i installed a t-56 in my 98 cobra, it wasnt till after that i found out that the speed sensor from the 04 wont work in my 98. i ordered a speedcal that the dm guy said would work for the conversion and am trying to install it, but when i try to use the online speedcal calculator...
  2. 98stangalang4v

    T-56 swap

    97kobra - i just did the t-56 swap in my 98 over the weekend... i too am still trying to find the fix for the speedo... a local (so called) "mustang specific" tuner shop, told me that the speed sensor cannot be calibrated for a 98 because the 03 sensor sends a digital signal and the 98 ecm uses...
  3. 98stangalang4v

    03 Cobra Tremec Tranny Swap Problem

    hahaha! i am doing just the opposite... over the weekend, i put an 03 cobra t-56 in my 98 cobra and at 20 mph, mine jumps to about 140! i am listening for an answer as well... :shrug:
  4. 98stangalang4v

    98 cobra with an '03 6 speed????

    oh and i did the swap in a day with help from a buddy... the only problem we ran into was the nuetral safety switch wires had to be extended because the 98's is on the driver side and the six speed's is on the passenger side... that was the only real change... as long as you have a driveshaft...
  5. 98stangalang4v

    98 cobra with an '03 6 speed????

    ive got a 98 cobra, 4.30's, and the tremec t-56... the t-45 was grinding and whining so it had to go.... the 6 speed is awesome with 4.30's... my only problem is that the speed sensor on the 04 cobra tranny is completely different, some tuning shops around here have given me different...
  6. 98stangalang4v

    03/04 -> 96 Tranny Swap

    silentbulllit - do you happen to have the part # for this speedo calibrator? i just swapped the 04 cobra t56 into my 98 cobra and the speed sensors are vastly different. i have talked to some mustang tuning shops, some say it can be calibrated with a tune and others say it wont.... im stuck...
  7. 98stangalang4v

    Fox 4 lug to 5 lug, stock axle length

    i work at an oreilly auto parts store and have done a little on the clock research on those front rotor 5 lug swaps... the exact perfect rotors to use are 88-92 lincoln mark series... same 10" diameter same bearings and seals as fox mustangs and same offset. they are probably the cheapest front...
  8. 98stangalang4v

    looking for info, input, and suggestions...

    ok i found out this... the deck hieght is about .35" inches taller on a 5.4 which DOES spread the heads apart, and there ARE 4.6 4v to 5.4 4v intake adapters just for that reason. and on the year models... there were two blocks for 2v 5.4's. one from 97-01 and a revised NVH block that is...
  9. 98stangalang4v

    how much

    from what i understand from my guys at strictly performance in houston TX.. the terminator engines are durable as well as bulletproof.. i always tell myself that if i can find an 03/04 with ANY amount of miles on it for under 20k$ that i would sell my baby and find a way to trade up... ha only...
  10. 98stangalang4v

    Questions about 99 Cobra

    haha... a 2001 might be a little bit easier to find...
  11. 98stangalang4v

    okay... i need a quick answer!

    i found a good deal on a local 01 4v intake. deal probably wont last very long... i am beginning to build a 4v 5.4. if the deck hieght on the 5.4 id taller, wouldn't that spread the heads apart a little? i want to know if i am going to need a special custom intake or will a factory cobra intake...
  12. 98stangalang4v

    looking for info, input, and suggestions...

    that what i was told as well and i got quite a steal on a complete 02 triton 5.4 today on my way to work... i do have one concern if the deck hieght is taller on the big bro engine, and i plan on 4v heads and valvetrain, then will a cobra factory intake(say... a 2001) still fit? ive never heard...
  13. 98stangalang4v

    looking for info, input, and suggestions...

    okay...my 4v 4.6 has about 125k on her, i want to start building a 4v 5.4 from a bare block. I have been told that 2v and 4v blocks are the same(had i known this before i would have done something more with the two 2v engines that i already have),but i have already sold myself one building a...
Top Bottom
Back
Forums
Menu