Search results

  1. H

    Tire Size 87 Gt

    This are rims a gonna buy...
  2. H

    Tire Size 87 Gt

    Hello, I have the following question: Will a 225/50/R17 tire on a 8" wide rim in the front of 87 GT rub? The car is not lowered!! thanks Frank (Netherlands)
  3. H

    reading fault codes

    Hello, Can somebody tell me whats the best device for reading my computer fault codes of my mustang 1994. I have also a lincoln Navigator 1999 with some fault codes. Is it possible to read both cars with the same device???? allready thanks.....
  4. H

    C6 Transmission for dragracing

    Thanks for the information guys
  5. H

    C6 Transmission for dragracing

    Hello, Thank you for your reply. Which company i must oder the parts?? I have found the website c4-c6.com....is that the right stuff!!!!!!! I want to oder the following parts: #1SX servo #1XXX forward drum #2WRB wide kevlar powerband #24RES Redeagle special (Includes #1XX direct...
  6. H

    C6 Transmission for dragracing

    Hello, I have a dragrace car that runs 10 low (a track in Holland). The car has the following specification: - mustang ‘67 - weight with driver 3550 pond - enigne 514 ci about 900 hp - camshaft (8000 rpm – redline 8500) - gears 3.91 - tire 26 inch. - 60 foot time 1.47 (without...
  7. H

    Automatic transmission

    hello Why is the 1 gear different in the drive or 1 ??????
  8. H

    Automatic transmission

    The problem is solved..........it was the servo how's engage the reverse band!!! the rubber of the servo was hard and seals not properly!!
  9. H

    Automatic transmission

    Hello, We have rebuild a C4 Automatic transmission. Everythink is perfect except the reserve. When you put the car in reserve the transmission doesn't respond. But if you give the car a little throttle the transmission responds and gets in reserve!!! Can somebody tell me whats wrong...
  10. H

    rod bearing clearance

    nobody????
  11. H

    rod bearing clearance

    hello, My big end (chevy 2.200) of the crank from my 514ci Ford has to be polished. I have oderd the following undersize beaings 0.010!! http://store.summitracing.com/partdetail.asp?part=CLE%2DCB743HDK10&autoview=sku I want to have a clearance of the rod bearing between 0.002 and...
  12. H

    rod bearing clearance

    can somebody tell me what the clearance is of the main bearings with the same set up!!
  13. H

    clearance piston to wall

    OK......a mean 4.445 or 4.450....(don't matter anymore) This clearance is also with the rods 0.002-0.0025 per diameter......0.001 - 0.00125 per side
  14. H

    rod bearing clearance

    thanks
  15. H

    clearance piston to wall

    hello, maby a stupid question.. If my piston has a diameter of 4.440 and the clearance thats needed is 0.0050 what is then the bore size !!!!! 4.445 or 4.460 greets Freek (from Holland)
  16. H

    rod bearing clearance

    Hello, I have a question about the rod bearing clearance. I have: - a 460 Siamese bore engine stroked to a 514ci. (0.080 overbore) - aluminium rods from manley - castrol R40 oil Can somebody tell me what the clearance should be of the rod bearing. Car is for dragrace...
  17. H

    wheels for a 1987 gt

    nobody!!
  18. H

    Mass air problems

    Hello I have a 1987 mustang with a mass air conversion from Pro-flow (1992). The car runs not well at idle, its bump up and down +/- 100 rpm and smells like hell ...unburend feul. (If the engine is cold it runs perfect but after 5 min. it runs bad as discribed above) The follow thinks i...
  19. H

    O2 sensors and code 41 & 91

    Hello, I' have a problem with O2 sensors. When a dump the code of the computer i'am getting code 41 and 91. The cars runs rich and smels like hell (unburned feul). The follow thinks I have done to get rid of this problem: - new O2 sensors!! - measure all the wires....there were all OK...
  20. H

    wire O2 sensors

    nobody!!!! The car is running very rich ...its stinks badly!!!
Top Bottom
Back
Forums
Menu