Search results

Hey all, before you say anything I have ordered my pushrod length measuring tool. But I have never used one before and want to know if anyone has setup the same as myself. I am running a stock bottom end with a TFS stage 1 cam and 200cc cast roush heads, made by World. 1.6 stud mount roller...

I am adding nitrous to my 91 GT, I plan on running a 100 shot with my NOS wet kit. I have a trickflow street heat intake, 70mm TB, BBK cold air intake, 70mm MAF, trickflow stage 1 cam, off road X pipe, flowmaster mufflers and stock heads for now........ The nitrous kit is all wired up with a NOS...

I have a 94/95 5.0 bellhousing for sale in great shape cleaned and primed ready for install. $130 free shipping!

I am going to be swapping a T5 from a 2001 Mustang v6 into my 91 fox. I know I need to swap the input shafts, but I was wondering what I should do for the tailshaft housing? the 99-04 T5's have the electric speedo and does not look like I can put my mechanical cable in the 2001 T5's VSS...

I got my stage 2 snow performance kit the other day in the mail. I am using my existing windshield wiper tank for my methanol but need to fine a place to mount my pump? I am trying to put it in the drivers side fender well some place and do not want to mount it in the trunk but do want to keep...

I have a procharged 02 GT I want to put methanol on this spring to add a little power and safety to my engine. I was wondering if my tuner could tune the ECU to pull timing if there was a pump failer or low pressure in the system to prevent from detonation? I was looking at "safe injection" from...

I am looking at getting a 03/04 cobra front bumper for my 02 GT and noticed that most of the chin spoilers are more then the bumper! I saw on ebay that they have one listed for the GT and cobra for around $100........So I was wondering if they were the same chin spoiler? or should I stay away...

I just picked up a 2002 3.8 T5 that I want to swap into my wifes 91 GT. I know all the options, getting the 94-95 Gt bellhousing, swapping input shafts because both the bellhousing and input shaft are 5/8 inch longer. But I was wondering if anyone has made a spacer plate to go between the...

Does anyone know were I can find a tubular front bumper support for my 02 Mustang gt? I am doin a cxracing intercooler upgrade and reduing all the piping and want some extra clearence and air flow to my intercooler but cant not find any for sale!!! I have found them for foxbodies but not 99-04...

I have been looking around but could not find the max amount of hp anyone has got with stock 2v heads on a forced induction engine. Does anyone know what you can make with a built bottom end, intake, cams, exhaust and say 15-16lbs of boost on stock unported heads? also all supporting mods...

I was wondering peoples opinion on 15" tires vs 18" tires my brother is always talking smack about my 18" rims and tires and would never buy anything bigger then a 15" because he says you cant get tracking. But I have a set of M/T drag radials on my 18" bullets and they stick ALL day on the...

can anyone tell me the Banjo bolt size for a 91 Mustang gt, for the split on the rear brakes. I lost my old bolt and now I need a new one and need the thred size and length! Thanks!

I was coming home the other night and gave it WOT at the passing lanes, after I got to the end I noticed my fuel pressure gauge was reading 20PSI during crusing speeds! when I listened there was a ping under boost so I took it easy the rest of the way home. The next day I started it and it was...

Hey everyone, Im having an issue with my 02 mustang gt. When I go to start it up it will crank and not start the first try, then the second try it is hard to start but it will start. After that it will run fine with no problems exept for a check engine light. After it has been ran for a little...

Does anyone know the part number for a 302 crank shaft repair sleeve or speedi sleeve? I am trying to buy one from summit racing but can't find it on there website. Or maybe a NAPA part number? Thanks!

What is a good Off-road X or H pipe that is cheap? I have looked at mac, pypes, Dr. gas, UPR, SLP, and Magnaflow. The best deal I have found was Pypes O/R X pipe stainless steel for $180 shipped on Ebay. But all the fourms I have read say they fit like S**T, but its hard to pass up a SS pipe for...

So I got back from performance dyno in NH yesterday and the numbers were 362hp and 372tq air/fuel was around 11.5 at WOT and he was running 15 degrees of timing due to old gas. He wrote me 2 tunes, one for 91 octane and one for 93 octane he said I could add more timing with my SCT Livewire when...

Does anyone know were I can find a wiring diagram for the gauge cluster on my 02' GT? I think the main ground or power wire has a loose connection because car will not start and run without me wiggling the right side harness. When i turn the key to the on position there is no power going to the...

I used a noid light to see that my injectors are not firing, I did some intercooler piping and removed my nitrous kit and wiring and now the car will not start. Also the gauge cluster does not get power exept a few of the bottom lights. car turns over and has spark and fuel pressure but no...

If anyone is interested My friend and I are putting together a Mustang Cruise on June 4th. It is for all mustangs and will be held in Ellsworth, Maine. We will cruise from there through the Acadian National Park loop road and into the town of Bar Harbor, Where we will be crashing the Annual...