Search results

I have had that happen too. My issue was that when I put my TPS back on it broke. This caused the IAC to try to compensate for the unknown throttle position, which caused a loud whistle. It was the air moving past the IAC that caused the noise. So check to see if your getting .7-1.0 volts...

I have a similar set up, just a bit less on the cubes and boost. I use 42# and a Lightning maf. I have HEARD that the LMAF has very good electronics which is highly accurate. Abaco (or whatever) are SUPPOSE to be good, however, I have never owned one or ever heard of the quality of one...

I have had three pairs of AFRs and their costumer service is great.

this is my 331 set up.... EECTuning.org • View topic - head/cam combo with 331 **finished biuld**

my fox showed no sign of damage to any mounting point of the axle either..... the previous owner probably took a corner too fast, spun out, and it a curb; this force could bend the mounts that hold the axle straight. that impact could shift the whole axle left or right (depending on what side...

as for the LMAF, go with the newer 90mm. the FORD pn is f68Z-12a690-aa. this is the proper wiring adapter. check ebay.... they also have inj. maf and maf adapter combos you can buy in a package. ..... Read my combo in my link, with that i use stock FPR and fuel rails and maintain a...

If you check out the link below you can read all about my new supercharged DART 331.:nice::nice: im currently running 42lbs inj. and a lightning MAF and I have yet to catch it going lean. The fuel pump has A LOT to do with higher rpm lean-outs too. make sure you have at least a 255gph...

Its been a long road getting everything together so I thought I would sum it up and let everyone know how it went. check out the link and see...... EECTuning.org • View topic - head/cam combo with 331 **finished biuld**

I happens dramatically when engine braking from a slope. However, it does not take long for the engine temp to drop if im, lets say, in third at 3000rpm and see traffic ahead and let off. then it may drop to about 175* or a bit lower. I see this on my tuning software (tweecer) in a numeric...

hey everyone, i just finished a build of a supercharged Dart 331 with afr 185 heads and a comp cams nx274hr. everything on this motor is new and i have been experiencing some funny temp readings lately. first, i have been running after market gauges for a long time including AFR, boost...

This is what I did.... (this should only be used on non emissions legal cars... DO NOT USE THIS SYSTEM IF YOU GO TO THE TRACK!!) Go to autozone and get... 6 ft of rubber 3/4 inch hose a new oil filler cap with a breather small rubber caps, these will be used to cap off the TB...

. That's what I'm about to do! I'm tired of hastling with this. Does anyone know if there has to be any other changes done to make the tko work after the bellhousing and cross member are changed hanged? Th Posted via Mobile Device

Hey, Im in the middle of getting forged 331 parts stuffed in a dart block and am also in the market for a new 5spd tranny. I have done quite a bit of research and still have came up clueless on what to do. I have talked to Gforce many times along with Astro performance about a T5. Both...

..Oil pump failed **UPDATE..NEW 331 COMBO** Long story short, I let my car war up and after about 5 min of idle i noticed i had no oil pressure. I noticed slight lifter clacking and thats when i noticed the oil pressure. I checked the gauge and it was working. I even unscrewed the...

NOPE! Read the StangNet Terms of Service please!

Im not a fan of street racing and don't do it, however, I did this time. On the freeway a GSXR 600 pulled up next to me and gave me a rev and a look like he wanted to run. luckily there were no cars around for at least a mile or two and it was too sweet to let it pass, so i when for it...

when i got my afrs in i was going to recheck all that zero lash stuff but i did not. i used all my old shim stuff on my afrs. it worked fine. then i called afr and double checked to see if they are TRULY stock bolt on replacement, they said yes. i called a couple of times to get different...

its not as bad as you think. the rear end did not fall off or anything but i did think that this was a big enough deal to warn others about.:D for no reason i double checked my bolts that hold my lakewood control arms on, both upper and lower, and most were very loose! :shrug: the car, i...

I know what you mean about turbo. i was looking at treadstone and their turbo kit for our cars was 200 bucks more that what i payed for my vortech:mad::mad::mad: BUT Cali likes the CARB # and apparently they are concerned about smog:shrug::shrug: when i saw that i almost just bought it...

some times valve train is noisy, especially when baffle is removed and new rockers are added. but if it is seems like its one ticking from each revolution then in prolly is a slightly collapse lifter. i would try replacing them. there is another recent post about a similar problem. follow...