Search results

  1. 8

    Flywheel And Starter

    Yes, it will work. Same diameter and number of teeth on flywheel. Why do you want to use an 11" clutch is my question. Aftermarket flywheel with provisions for both 10.5" and 11" is what you will find with a 6 bolt crank.
  2. 8

    Flywheel And Starter

    You have a T45 not a T5. Romeo motor with a 6 bolt flywheel needs a 10.5" clutch. You can't use the 11" clutch. Flywheel is not 11", the dowels on it are drilled for a 10.5" clutch. So in short, T45 10 spline input shaft, 6 bolt flywheel for use with a 10.5" clutch kit. Hope this helps.
  3. 8

    Pi Head Install

    Positioning tool is used only when removal of cams is being performed. This keeps you from removing the timing cover to access the timing chains. Saves a bunch of work. Since you are removing and replacing heads, you would have to re-time the motor. Search PI swaps, there are a lot of...
  4. 8

    Tranny Is Hard To Put In Gear From Stop

    how did you try adjusting the cable? cable may have stretched , or is binding somewhere, not allowing full disengagement. try adjusting again , see if it makes any difference. also what year is the car?
  5. 8

    Photo Request: 96 Gt

    defrost does the same to mine.(when it used to work) grab a volt meter and check what the voltage is at the alt and the battery. make sure the connections at the posts are tight and clean.
  6. 8

    Photo Request: 96 Gt

    No firewall ground, just the ones by the radiator/left headlight, and the main ground from the left motor mount to block. There is a fuel rail ground that is by the firewall. That just gets capped onto a valve cover stud. Let me know if you still need pics.
  7. 8

    Trying to find some recommendations for replacement radiators

    How about the OEM 03-04 cobra rad? Heard it was good bang for the buck.
  8. 8

    Mustang fresh rebuilt wont start

    disconnect the cam pos sensor see if thst helps.
  9. 8

    Something Fishy...

    hows your heater core? any fogging around the windshield, damp carpets? old coolant can have a slight fishy aroma to it.
  10. 8

    Replacing Steering Rack Bushings

    Yes, disconnect the steering shaft. It allows the rack to move forward to put the bushings in place.
  11. 8

    Broke rear sway bar

    Same with me. Been a month without it, hard driving, highway speeds,cant tell its not there. Having a hard time ponying up the money to replace it.
  12. 8

    Swapping throttle body and plenum??

    i dont think hp gains are what make this bolt-on worth it or not. it is throttle response. the car will feel "lighter" as it will react differently with the amount of pedal you give. (until you get used to it) do it!
  13. 8

    Need help immediatly. working on car

    torched mine out too, PITA job that was.
  14. 8

    Block heater leak?

    ive had mine let go on my 96, easy to replace though.
  15. 8

    Have an oil leak around oil filter

    yes there is a gasket behind the oil filter adapter, mine developed a small leak there as well. gasket is cheap ^20.00, and easy to install, just a little messy because of the oil and coolant good luck
  16. 8

    96 conv. cobra paint code

    thanks , ill update when i get hard info. so far it looks sketchy, but who knows!
  17. 8

    96 conv. cobra paint code

    im getting the complete VIN tonight, but when he saw it he did notice that the engine identifier letter is V, which is Cobra right? Do you know which number in the VIN would identify it as a convertible? Thanks for the info!
  18. 8

    96 conv. cobra paint code

    Hi all, my brother is looking at a 96 convertible cobra 5 spd thats been painted, and was trying to find out the original paint color. the paint code on the plate is RC (platinum?) looking through some websites , i thought the 96 cobra had only 4 colors to choose from and platinum was not...
  19. 8

    Rattling at low RPM

    i had the same thing, drove me nuts! turned out to be the inspection cover on the tranny. even though the bolts were tight it had enough slack to rattle at low RPMs. i just wedged some cork gasket material in the spaces and done!
  20. 8

    ebrake help needed (yes I searched)

    remove the center console, looking down on the brake handle from the drivers seat, you will see a "latch" that acts as a stop on a small gear. move the handle up and down and you will see what i mean, this is the automatic adjuster, when there is too much slack the gear moves up a tooth putting...
Top Bottom
Back
Forums
Menu