Search results

  1. SonicStangGT

    Custom Turbo Exhaust

    Well I'm still running stock catback with weld in flowmasters(2 1/4). My tuner told me its holding me back at least 10-15 hp. So I've bought a slp catback minus the mufflers nd want to put 2 1/2 race flowmasters. But this is my question, would it be better since I'm have a turbo with a 3''...
  2. SonicStangGT

    04 Mustang Drag Wheel Question

    I'm looking at getting some rear prostars for the track and want to make sure that I'm getting the right size and backspacing. looking at 15x8 with 5.5 bs or 15x10 with 6.5 bs. I have 275/60/15 drag radials and want to run the 15x10 with 6.5 bs. Just wanna make sure right I'm getting the...
  3. SonicStangGT

    Got my car tuned finally.

    Went to Piedmont Custom Motorsports and I had my stang tuned and made 400 hp and 420 tq on 9psi. Was going to run 11-12 psi but maxed my fuel pump out so gonna have to wait. They did a great job and couldnt have went to a better place. Anybody around North Carolina wanting a dyno tune should...
  4. SonicStangGT

    Turbo wastegate and bov problems

    Ok, been a long summer for me, got my on3 turbo kit this summer, but been so busy havent had time time to install till now. Got a few problems that I hope someone can assit me with. I have a appt. woth Piedmont Custom Motorsports Thrusday morning for a dyno tune but Like i said theres a few...
  5. SonicStangGT

    Adjustable Fuel Pressure Regulator On 2004 Mustang Gt

    Ok got turbo kit on finally and now getting ready to take a get a dyno tune. I called them this morning to set up a time and they were asking me what king of fuel pump, injectors,MAF Im running and then asked me if I had a adjustable fuel pressure regulator. I've looked and cant find one that...
  6. SonicStangGT

    Been Awile Since I Posted, Got New Goodies.

    Just picked up a forward facing On3 performance turbo kit. Still have to buy K member, fuel pump, maf. I wanted to get the big expense out of the way.
  7. SonicStangGT

    Hanging idle

    Ok i already did the IAC trick that I found in a search on stangnet and it worked untill the computer learned what I was doing. Now the computer is setting a high idle speed code and it seems that the IAC trick only works for a little bit. If I clear the code it seems to work fine, but after...
  8. SonicStangGT

    Removing oil pan.

    Is it possible to remove the oil pan with the motor in the car. Can you loosen the motor mounts and pick the motor up with a engine lift to get enough room to remove it or is there another way. Thanks for any info.
  9. SonicStangGT

    stock 04 gt pistons

    I'am in the process of replacing my flat top pistons with new take out pistons and I have run into a snag. There are no marks or notchs to indicate the front of the piston. On my flat tops there are notchs, but on the stock pistons I bought , there are just numbers and colored dots on top. On...
  10. SonicStangGT

    Installing 3v into my 04 GT

    Thinking of installing a 3v because my motor has to come back out and can get a good deal on a 3v right know. My ? is if I get the motor, wiring harness, and a ecu will the motor bolt to my k-member and also will my tranny. I know that they have a 3650 too, and they have a hydr. clutch instead...
  11. SonicStangGT

    Questions on installing 3v into my 04 GT

    I'am thinking of installing a 3v in my car and was wondering if I had the motor, wiring harness, and ecu would it bolt up to the K-member. Also will my 3650 tranny bolt up along with my 11" clutch. I know that the new stangs have them to, but I think they have a hyd. clutch, but I have a cable...
  12. SonicStangGT

    Flat top pistons suck.

    Well about two weeks ago I was driving my car and every since I put the motor back in something had not been right with the tranny. Well missed fourth gear some how and bent a valve on the driver side. Did a compression check and on that cylinder I have 25 psi and I think its supposed to be...
  13. SonicStangGT

    Never whored car, tell me what you think

    Well got the motor back in my car yesterday and got it running. Decided that I would clean it up and post some pics. Going to get it dynoed sometime time this week and leave for the beach on FRIDAY night after work.:D
  14. SonicStangGT

    Engine build back on track.

    Well got the stock cams tuesday and finished putting back together after work today. Heres some picks before I start putting it back in tommorrow. Mustang week here I come.:D
  15. SonicStangGT

    Engine build gone wrong! What combo due I need?

    I'am building my 4.6 back with stock 96 cobra flat top pistons with flycuts. Also installing Comp 278's. My problem is that when I'am trying to degree them I can't even get through a whole revolution without the intake valve having PTVC. :shrug: What piston combo can I use so that I don't...
  16. SonicStangGT

    Looking For a writeup on Degreeing a 2 Valve

    Me and my dad are about to degree my motor and he's done sb fords and chevys, but never a ohc. We just need to find a good write up thats better than what Comp Cams has and I only find bits and pieces when I google it, just a couple of pics and a couple of paragraphs. Thanks for any help.:D
  17. SonicStangGT

    Need HELP, starting engine build

    I just got my pistons back from getting flycut and I cant remember where the rod bearing notches go. Do they go on the outside or to the inside. I had them on my stock stuff but the guy at the machine shop took them all off and hes not open till monday. I know the notches on the pistons go...
  18. SonicStangGT

    Degreeing 2 valve cams

    I getting ready to put my motor back together and I'am installing 278's and they have to be degreed. I need a piston stop and was talking to comp cams and they dont have one for the 4.6, wondering if anyone knew where to get one. Also need some way to attach the degree wheel to crank. Comp...
  19. SonicStangGT

    Ferrera Oversize valves

    Does anyone know where to get them. I really doesn't matter if they are ferrera or manley, just need to know where I can find them, THANKS.
  20. SonicStangGT

    Steeda UD Pullies

    Are they worth the $180. I bought a set of BBK, but found out they are the cheap ones that is a add on to your crank pully. So I sold and now am looking at Steeda's kit, there kit replaces the crank pully. Just wondering if they really make power or if I should just skip. Thanks