Search results

  1. 95Cbra5O

    Rear End Noise - Bad Carrier Bearings

    I have a 2014 GT with about 29,000 miles on it. I started getting a metal on metal noise from the rear end about 5,000 miles ago. So I took it to the dealership and they ended up replacing the carrier bearings. I picked it up and it seemed to be somewhat better. I thought all noise I was hearing...
  2. 95Cbra5O

    Cooling Fan Won't Come On

    Yeah it was the ect sensor. I was unaware that there were two sensor dealing with coolant temp. Thanks for the help!
  3. 95Cbra5O

    Cooling Fan Won't Come On

    Just ran KOEO test. Fan kicked on. No codes.
  4. 95Cbra5O

    Cooling Fan Won't Come On

    Yeah I was talking about the ccrm. I have also already replaced the coolant temp sensor. It has been going on for a while. It doesn't get driven but every couple of months so it hasn't been a huge priority to fix but I'm to the point where I would like to figure it out. Thanks
  5. 95Cbra5O

    Cooling Fan Won't Come On

    The cooling fan won't come on at all. Not even with the a/c on. Checked all fuses. Replaced fan motor and relay module. Still no luck. Any help is appreciated!
  6. 95Cbra5O

    Cleaning Throttle Body

    I just pulled off the throttle body on my 95 and it has a lot of build up on it. Also the intake manifold has quite a bit of build up on the portion I can see with just the throttle body off. Is there anything I can do to clean the intake manifold without taking the whole thing off? Thanks...
  7. 95Cbra5O

    Air only comes out of defroster vents?

    No matter what setting it is on the air will only come out of the defroster vents. Does anyone know what the problem is? Thanks for any input.
  8. 95Cbra5O

    Car stalls when braking..

    Thanks hissin I really appreciate it. I acutally have the old one that has 2 teeth left on it I might throw that in for now.
  9. 95Cbra5O

    Car stalls when braking..

    Just got my car back from the shop. It had some transmission work, brakes, and a fuel filter done. They found that the speedometer gear was pretty torn up so they ordered a new one. It hasn't come in yet but I needed the car so they let me take it without the gear in it. The speedometer...
  10. 95Cbra5O

    Difference in 95 cobra transmission?

    Does anyone know if the t5 transmission that Ford put in the cobras is any differernt than the ones that they put in the other mustangs? Thanks for the help.
  11. 95Cbra5O

    Header install in progress...

    I have done the passenger side and am going to try and finish up the drivers side tomorrow. The problem I am worried about is the bolt closest to the front of the car, it is quite tricky to get to. Does anyone remember what they used to get to it when they did their header swap? Thanks
  12. 95Cbra5O

    Drama with the repair shop...

    Just got it back, no noise...yet. They tried to get me to pay for the install and that wasn't going to happen. The problem now is that the clutch feels like crap. It is really loose at the top. They said they removed all of the preloads so, "there is no way the throw out bearing can go out...
  13. 95Cbra5O

    Drama with the repair shop...

    That is good to hear. I hope this different throwout bearing takes care of it.
  14. 95Cbra5O

    Drama with the repair shop...

    Yeah I have been reading some other threads and found out that a ford one might be better so I think they are going to go with that. I wish I would have gone with the king cobra. Thanks
  15. 95Cbra5O

    Drama with the repair shop...

    Nope no aftermarket clutch cable. Thanks
  16. 95Cbra5O

    Drama with the repair shop...

    About month ago I had a new clutch put in. They raved about Luk clutches so I decided to let them go with what they know. Then about a week after that I started getting a whining noise and as soon as I pushed on the clutch the noise stops. I take the car back and they tell me it is the throw...
  17. 95Cbra5O

    What lenth of Stage 8 header bolts?

    Yeah I felt like the 3/4" inch ones are too short as well. I ended up ordering the 1" ones, I will post how it goes when I put them on later on this week. I have been strictened with exhaust leaks for a while now and am ready to be rid of it. It just murders the performance which makes the...
  18. 95Cbra5O

    What lenth of Stage 8 header bolts?

    I think the flange is 3/8" in. and the gasket is 1/8" in. I keep leaning towards the 1" but having them too long will take away the reason for getting them.
  19. 95Cbra5O

    What length stage 8 bolts?

    I am about to order some stage 8 locking header bolts, what length should I get, 3/4" or 1"? I have percy's seal 4 good gaskets on there but the bolts keep backing out. If I reuse these gaskets should I pull them out and clean them off before I put these bolts on? Thanks for the help. Brandon
  20. 95Cbra5O

    What lenth of Stage 8 header bolts?

    I am about to order some stage 8 locking header bolts should I get the 3/4" or 1" length bolts? I have percy's seal 4 good gaskets on there but the bolts keep backing out. If I reuse these gaskets should I pull them out and clean them off before I put these bolts on? Thanks for the help...