Search results

Asking for $80, Ill meet buyer if in LA area. Extra for shipping.

@Noobz347 I also have an 8CB computer off an 06/89 mustang hardtop automatic transmission 4cylinder mustang. Do you have a list for those series mustangs with 4 Cylinders?

@jrichker I used the noid light to confirm that the PIP is working and the injectors are getting pulsation and im getting fuel on the spark plugs. I am also getting spark. And taking out the SPOUT connector doesn't make a difference, or set a code. I even took out the TFI and checked the...

Ok, so looking at a few different wiring diagrams, this is the exact wiring setup that I have. http://www.veryuseful.com/mustang/te...ng_Diagram.gif So today I basically tested all the Fuel Pump Relay wires. I started with the red wire from EEC/PCM Relay to the Fuel Pump Relay. I measured 0.2...

I have only removed the TFI, I did not remove/pull up on the distributor when I loosened the distributor hold down bolt. I know I could have messed up the timing and I was exteremly careful. I even made 3 lines using a sharpie to put the distributor back to its original timing. I have the...

Ok, so i plugged in a new BARO sensor, and it still won't start. But I also accidentally retrieved codes with the BARO sensor unplugged and got the code 22. So I plugged it in, erased the codes, and retested for codes. Now its not even giving me code 96 Just code 11: System OK (O,CM) - So I'm...

Sorry for the mixup, I was testing BARO sensor, not the MAP sensor. I got the 5V reference and good ground, but when I set my Multimeter to Hertz frequency %, it measures 0.00. Im testing the middle wire, is that correct?

After I cleaned the Fuel Injector Harness connector ("Salt&Pepper shakers) the code 96 went away and only 10 and 11 were left. @vfast which wire should i check? It cranks, and voltage goes to Comp/Fuel Pump/Inj./Coil/Spark @jAEded Checked all my hoses, and replaced relay, and tested for...

Yes and all the tests are coming out good, but gota question... If i use a noid light to plug the spout connector, it should flash just like checking for switching on a fuel injection harness right?

Ive pretty much done EVERYTHING you've said on your posts jrichker, even on the AllFordMustangs website I've seen you posts and tested like you said. I measured 12volts at the injectors and also used a noid light to test all the injectors that I can get to, (good), without removing the intake...

The computer pictured was taken off a 1988 Ford Mustang V8 5.0L Automatic Transmission Convertible. The computer program code is 8LG which is similarly compatable with other makes and models of mustangs of the same year range. The vehicle was in dissasembly and I am unable to detirmine if...

Hey Guys, need some help from fellow enthusiasts. I've been banging my head for a month since my Mustang died on me. :bang: So after I pick up my girl and leave to get burgers, I feel some throttle hesitation and make it to the burger joint "ok". After eating, my car starts up, stumbles a few...

Hey guys, like the title says, my needle on my oil pressure gauge sways back an forth between low and high normal. This will happen when i slow down or speed up/ at rest at the stoplight. This happened after i changed the oil with 10w-30 Castrol oil, and exactly next week i flushed out the...

Hey guys. Im new here, an all you guys sound pretty professional. I failed my smog test for my 1991 Mustang 5.0. My uncle put a chip in and its been running rich for 3yrs. an coated the catalytic converters with hydrocarbons, causing it to fail smog. How would i go about to make the...